110 rpm driven by 500 mm diameter flat rolling electric motor available on rolling mill are rotated with. The speed at which flat material rolled in neutral cross-section passes between rollers is m/s which of the following? Please select one: A.2,88 B.1,44 C.14,4 D.28,8 E.0,288

110 rpm driven by 500 mm diameter flat rolling electric motor available on rolling mill are rotated with. The speed at which flat material rolled in neutral cross-section passes between rollers is m/s which of the following? Please select one: A.2,88 B.1,44 C.14,4 D.28,8 E.0,288

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7-2 Problem 7-2 Section of a shalt containing a grinding-relief groove. Unless otherwise specified, the diameter at the root of the groove d, d-2. and though the section of diameter d is ground, the root of the groove is still a machined surface The section of shaft shown in the figure is to be designed to approximate relative sizes of d = 0.75D and r = D/20 with diameter d conforming to that of standard metric rolling-bearing bore sizes. The shaft is to be made of SAE 2340 steel, heat-treated to obtain minimum strengths in the shoulder area of 1226-MPa ultimate tensile strength and 1130-MPa yield strength with a Brinell hardness not less than 368. At the shoulder the shaft is subjected to a completely reversed bending moment of 70 Nm, accompanied by a steady torsion of 45 Nm. Use a design factor of 2.5 and size the shaft for an infinite life.
How is the angle of twist of a circular shaft determined?
An engine, running at 350 r.p.m., drives a line shaft by means of a belt. The engine pulley is 950 mm diameter and the pulley on the line shaft being 550 mm. A 900 mm diameter pulley on the line shaft drives a 150 mm diameter pulley keyed to a dynamo shaft. Find the speed of the dynamo shaft, when 1. there is no slip, and 2. there is a slip of 2% at each drive.
73 ll 6 O ... The pitch circle radius multiplied by the cosine of the pressure angle. Q3:- The increase of the contact ratio is desirable in gearing design because of:- * All of these The number of teeth will be increased in the engagement region More strength and more gear life will be achieved Smoother and faster motion None of these Q4:- To get best gearing design, it requires to:- * Increase sliding None of these Decrease sliding
5. What do you understand by 'fluctuation of energy' and 'maximum fluctuation of energy'. 6. Define 'coefficient of fluctuation of energy'. 7. Discuss the various types of stresses induced in a flywheel rim. 8. Explain the procedure for determining the size and mass of a flywheel with the help of a turning moment diagram.
How the sec (alpha) value is measured 29/2? Can you please describe the circled line in details.Thank you
Pls answer thank you! The equivalent twisting moment of a shaft under a torque of 5,000 in-lb and a bending moment of 8,000 in-lb, and having a diameter of 2 inches is _________.
ANSWER NO. 5 ONLY
ANSWER NO. 9 ONLY
HW12 The gearing of a machine tool is shown in the Figure below. The motor shaft is connected to gear A and rotates at 1500 r.p.m. The gear wheels B, C, D and E are fixed to parallel shafts rotating together. The final gear F is fixed on the output shaft. Fined: 1-the speed of gear F 2- rotating speed of gears (B, C, D and E) The number of teeth on each gear are as given below: Gear A B C D E F No. of teeth 25 35 90 30 80 60 + A B E+ D F LL
ANSWER NO. 6 ONLY
6. 5 3 Arm 6. 2 Arm Arm 2 3 1 Bearing Given N2 = 30, N3 = 25, N4 =45, N5 = 40, N6 = 200 W2 = 240 rpm ccw, warm = 120 rpm cw, T2 = 12 ft-lb Show your work. Answers without work will not be accepted a. Identify the gear sets. b. Determine the velocity gear train ratio and the angular velocity of gear 6. c. Determine the torque gear train ratio and output torque of gear 6.