A lathe is capable of spinning a cylindrical solid aluminium bar of radius 2.4 cm and length 75 cm up to a the required angular speed of 12000 rad s- in just 1.3 s. (PA 2700 kg m, Pwood 700 kg m1 What torque is the fathe capable of exerting? 1- 4 4N'm (2.s.f) ( Submit Answer Incorrect. Tries 3/5 Previous Tries

Q: A rotating shaft carries three unbalanced masses of 4 kg, 3 kg, and 2.4 kg at radial distances of 75…

A:

Q: have already asked this question twice. Please only answer this problem if you can answer explicitly…

A:

Q: 10. What is the minimum diameter in mm of a steel shaft which will be used to operate a 14 kN-m…

A:

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: The Ray Precision Engineering company uses CNC Lathe machine. The reliabilit of Gear Box of CNC…

A:

Q: "Design a shaft face journal bearing for a fixed radial load of 1500 lb, while the shaft rotates at…

A: Given Load = 1500lb N = 850 rpm ==85060=14.166 rev/s D = 2.1 in To find Design of journal In this…

Q: Which of the following does Newton's first law of motion describe?

A: Option (a) Inertia  is correct option

Q: 6. Four cylinders rolling in opposite directions has a speed ratio of AB.C:D = 5:2:3:4. If center…

A: Let the diameters of each cylinders be - DA, DB, DC and DD . The center distance is given by -DA2+…

Q: submit any example for shaft and gear and design them finding the bellow 1- the contact stress for…

A: given; (a)the contact stress for the shaft and gear (b)the bending stress for the shaft and gear

Q: A metric thread of pitch 2 mm and thread angle 60° is inspected for its pitch diameter using 3 wire…

A: Given:Pitch, P=2 mmThread angle, 2θ= 60oθ=30o

Q: A 48 in diameter diamond saw blade is mounted on a pulley driven steel shaft, requiring a blade…

A: Given 48 in diameter diamond saw Angular velocity = 150 ft/sec Power = 125 hp Rotation = 1200 rpm…

Q: 9. What is the polar moment of inertia (in*) of a solid shaft that has a torque of 2 kN-m and a…

A:

Q: Falcon company Nizwa is conducting a campus interview to you.  You are asked to design the propeller…

A:

Q: answer 12

A: The sum of the length of the shortest and the longest of a planar quadrilateral linkage if less than…

Q: Determine the maximum mass (kg) that can be lifted at E if the 10-HP motor A has a maximum rotation…

A: Please find the solution below

Q: I have a 52100 steel hollow shaft, that will be threaded into a 1 inch thick plate of aluminum 7075.…

A: Step 1:For a steel shaft threaded into an aluminum plate, it's crucial to consider the potential for…

Q: What is the axis yielding?

A: A yielding is phenomena of give up to something like external pressure. to yield something does not…

Q: A hollow round steel shaft has a torque of 600 ft-lb. The shaft has an outside diameter of 1.25 in,…

A:

Q: The motorcycle has a kerb mass of 239 kg and test rider's mass was recorded as 76.35 kg. The wheels…

A: The snapshot of idleness of a body about a hub is at times addressed utilizing the radius of…

Q: what is the polar moment of inertia (in^4) of a solid shaft that has a torque of 2Kn-m and a stress…

A:

Q: Quest-5 b, The distance between two parallel shafts connected by Oldham's coupling is 25 mm. The…

A: The distance between two parallel shafts connected by Oldham's coupling r = 25 mm.The driving shaft…

Q: 4) The criterion of constraints for a kinematic chain having plane motion is given by the equation:

A:

Q: 8) A five-link planar mechanism with five revolute pairs (one link is fixed). The number of degrees…

A:

Q: The outside diameter of a hollow shat is 1.6 times the inside diameter. When transmitting 420 W of…

A:

Q: Problem # 4: The turbine motor moving at 378 rev/ min can produce 2.5 hp. The shaft diameter is 1.25…

A: Let T=Torque developed in the shaft d= diameter of shaft =1.25inches=0.03175m P = Power of…

Q: If a wheel is subjected to a torque of 180 ft-lbs and the wheel's outer diameter is 14", what force…

A: This question is based on the concept of Mechanics.

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.