11.10 (A/B). A load of 2 kN falls through 25 mm on to a stopat the end of a vertical bar 4 m long, 600 mm2 cross- sectional area and rigidly fixed at its other end. Determine the instantancous stress and elongation of the bar E= 200 GN/m². (94.7 MN/m2, 1.9 mm.

11.10 (A/B). A load of 2 kN falls through 25 mm on to a stopat the end of a vertical bar 4 m long, 600 mm2 cross- sectional area and rigidly fixed at its other end. Determine the instantancous stress and elongation of the bar E= 200 GN/m². (94.7 MN/m2, 1.9 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Polycarbonate bars (1) and (2) are attached at their lower ends to a slider block at B that travels vertically inside of a fixed smooth slot. Load P is applied to the slider block. Each bar has a cross-sectional area of 85 mm2, a lenght of 1.25 m, and an elastic modulus E = 8GPa. Use dimensions of a = 1.15 m and b = 0.90 m. For an applied load of P =1700 N, determine: (a) the forces in bars (1) and (2) (b) the defection at B of the slider block
7.5 B(1) Refer to Figure 7.13, which shows a flexible rectangular area. Given: B₁ 1.22 m, B₂ 1.83 m, L₁ = 2.44 m, and L₂= 3.05 m. If the area is subjected to a uniform load of 144 kN/m², determine the stress increase at a depth of 3.05 m located immediately below point O. B(2) 2 = (1)- 3 4 L(2)- Figure 7.13 Stress below any point of a loaded flexible rectangular area
II. A post tapers uniformly from a diameter d at the upper end to a larger diameter D at the lower end, as shown. It supports an axial load of P. Given allowable stress of S, the post's dimension can be determined using the formula o=P/A. For structural safety, what must be the area in this formula? The lower, middle, or upper cross- section of the post? Why? Upper Area Middle Area Lower Area
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1320 mm². Assume a = 2.4 m, b = 9.7 m, and c = 3.6 m. If P = 60 kN and Q = 70 kN, determine the normal stress in each member. a Answers: OAB = i MPa (C) MPa (Т) i MPa (Т)
Problem 1A steel wire is 6 m long, hanging vertically supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 4mm. E = 200, 000 MPa.
A steel rod is stretched between two rigid walls and carries a tensile load of 5000 N at 20°C. If the allowable stress is not to exceed 130 MN/m² at -20 °C, what is the minimum diameter of the rod? Assume k = 11.7 µm/(m-°C); E = 200 Gpa A. 10.22 mm B. 11.22 mm C. 12.22 mm D. 13.22 mm Please solve the Problem elaborately and Refer Machine Elements and Stresses Equations from the figures or use other shortcut Methods you have or you may Solve both or in more different methods the better ?. Your solution will be use as reference for my Future Board Exam preparation/review/study. Thank you so much dear your work will be appreciated much and rated excellently.
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 11 mm². The cross-sectional area of rod (2) is 14 mm2. For a uniformly distributed load of w = 4.1 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.35 m. A (1) (2) a L. Answer: a = i m
PROBLEM NO. 4 In Fig. 4, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 129 C. The 0.5-mm gap exists at 28 C (0.59 mm 399 mm A Aluminum A = 2888 mm² E = 75 GPa α = 23 x 10°/°C 258 mm B Stainless Steel A = 899 mm² E = 190 GPa α = 17.3 x 10/°C
PHILPS 2 Concepts EA/Documents/Week12 Compatibility 21-22-1%20(1).pdf 30 / 31 100% PROBLEM 2.35 The 1.35 m concrete post is reinforced with six steel bars, each with a 28 mm diameter. 450 mm Knowing that E, = 200 GPa and E, = 29 GPa, determine the normal stresses in the 1.35 m steel and in the concrete when a 1560 kN axial centric force P is applied to the post. [Ans. o = -59.5 MPa; o̟ = -8.63 MPa] Fig. P2.35 Seašon's Greetínas ·
A horizontal bar, fixed at one end (x = 0), has a length of 1 m. and cross-sectional area of 100 mm2 Its elastic modulus varies along its length as given by E(x) = 100e-x GPa, where is the length coordinate (in m) along the axis of the bar. An axial tensile load of 10 KN is applied at the free end (x = 1). The axial displacement of the free end is..... mm
A simply supported reinforced concrete beam carries a uniformly distributed load of 12 kN/m on a span of 4 m. The beam has a rectangular cross section 250 mm wide by 450 mm deep, with three 20 mm diameter steel bars placed 60 mm from the bottom of the beam, as shown below. The moduli of elasticity for the concrete and steel are 15 GPa and 200 GPa, respectively. Determine the average tensile stress in the steel and the maximum compressive stress in the concrete at the section of maximum bending moment. 450 mm 250 mm 60 mm
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. A) Determine the magnitude of load P. Express your answer in kips (rounded to the nearest hundredths.) B) Determine the shear stress on plane AB. Express your answer in ksi (rounded to the nearest tenths.)