Problem 1A steel wire is 6 m long,, hanging vertically supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 4mm. E = 200, 000 MPa. %3D

Problem 1A steel wire is 6 m long,, hanging vertically supports a load of 2000N. Neglecting the weight of the wire, determine the required diameter if the stress is not to exceed 140 MPa and the total elongation is not to exceed 4mm. E = 200, 000 MPa. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A replacement disc consists of the tube Cwith larger diameter of 4 cm, the cylindrical core B with the diameter of 2 cm and two relatively rigid discs on both ends. The disc replacement placed between vertebrae is under compressive force of 400N. The corresponding moduli of elasticity are Ec=10MPA and EB=20MPa. Determine the stress in the tube A and the core B. F Rigid parts 1cm C 2om 4cm F (Answer: OB = 509.3KPA, oc = 254.6KPA) 254.6KРа) %3D
Let’s consider a rod having a solid circular cross-section with diameter of 6 mm and it is made of a material having a Young’s modulus E = 200 Gpa and a Poisson’s ratio of 0.3. If a tensile force F is subjected to that rod cross-section, the diameter becomes 5.995 mm. determine the applied force F.
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A=500 mm STEEL L-4 m A-400 mm E=80 GPa E-200 GPa 3 m 5 m P.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 22 ksi, and the normal stress in steel rod (3) must be limited to 14 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 9 kips, Q = 5 kips, R = 20 kips and S = 30 kips. (1) VQ B R (2) C (3) D
A spherical pressure vessel has an inside diameter of 4.9 m and a wall thickness of 17 mm. The 0.27] that has a yield strength vessel will be constructed from a special steel [E = 224 GPa; v = of 250 MPa. If the internal pressure in the vessel is 1410 kPa, determine (a) the normal stress in the vessel wall. Answer in MPa rounded-off to 1 decimal place.
A tie rod of ¼ inch diameter is used to hold a plaster wall in place. The tensile stress in the rod caused by load P is 20 ksi. Find the diameter “d” (to the nearest 1/6 inch) of the washer that keeps the bearing stress between the plaster and the washer from exceeding 300 psi.
Don't waste my question please, I need the solution don't just capy the answer that I give there.
Calculate the smallest area of each cable if the stress is not to exceed 76 000 KPa in bronze and 118 MPa in steel if a homogeneous 778 000 g bar AB is supported at either end by a cable.
Problem 1 The figure shown is a hanger made of a round ½" diameter steel rod, subjected with a load of 5 kips. The Modulus of Elasticity of steel is 29000 ksi. Determine the tensile stress and the elongation in the hanger. TI P=5k 10'-0"
3) At room temperature (20 °C) a 0.8 mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 120 °C, determine (a) the normal stress in the aluminum rod, (b) the change in length of the aluminum rod Bronze: Aluminum: Steel: Area: 1000 mm2 Area: 2000 mm2 Area: 1500 mm2 a = 18.4 x 10-6 E = 103 GPa a = 23.6x 10-6 E = 75 GPa a = 17.3 x 10-6 E = 190 GPa %3D %3D 0.8 mm 100 mm 150 mm 300 mm Bronze Al Steel
A cantilever beam, 80 mm wide by 260 mm high and 9 m long, carries a load that varies uniformly from zero at the free end to 1200 N/m at the wall. Determine the magnitude of the stress in a fiber 60 mm from the top of the beam at a section 4 m from the free end. Answer must be in MPa
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 19 ksi, the normal stress in brass rod (2) must be limited to 22 ksi, and the normal stress in steel rod (3) must be limited to 13 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 7 kips, Q = 2 kips, R = 16 kips and S = 20 kips.