*11-64. The pin is used to connect the three links together. Due to wear, the load is distributed over the top and bottom of the pin as shown on the free-body diagram. If the diameter of the pin is 10 mm, determine the maximum bending stress on the cross-sectional area at the center section a-a. For the solution it is first necessary to determine the kad intensities wi and w 00N 25 m Domm 40 mm 18IN 1800N

Q: The way to the column where the loading status is seen determine the P load required for the 5 mm…

A: Given that,

Q: Below Figure shows the section of an angle purlin. A bending moment of 5 kN.m is applied to the…

A:

Q: *10-8. The solid shaft is fixed to the support at Cand subjected to the torsional loadings shown.…

A: Given data as per question The radius of bar =75 mm ecentricity of point A = 50 mm ecentricity of…

Q: The Douglas Fir beam is reinforced with A-992 steel straps at its sides. Determine the maximum…

A: The given problems is of composite beams with two different materials. One method to solve such…

Q: In a pipe of 90mm diameter water is flowing with a mean velocity of 2 m/s and at a gauge pressure of…

A:

Q: N in 1 in .9 y 12 in in D C B A -in

A:

Q: 0.5 in.3 in C 0.5 in. 3 in. 10 in. 0.5 in. B M

A: The centroid of the given figure is-The centroidal moment of inertia-

Q: The hook is subjected to the force of 60 lb Determine the state of stress at point A at section a-a.…

A: Part A: Write the given data. F=60 lbd=0.5 in

Q: The rectangular bar carries a load of P = 102 KN and is connected to the support bracket with a…

A:

Q: Determine the average shear stress developed in the nails within region AB of the beam. The nails…

A: Step 1: Step 2: Step 3: Step 4:

Q: Determine moment that will produce a maximum stress of 60 MPa on the cross section. To 3 significant…

A:

Q: 1-1. The shaft is supported by a smooth thrust bearing at B and a journal bearing at C. Determine…

A:

Q: Determine the bending strain energy in the simply supported beam. EI is constant.

A: Evaluate the total load on the beam as follows. F=12w0×L2+12w0×L2=12w0L If the total load is…

Q: 10-73. The shaft is made of L2 tool steel, has a diameter of 40 mm, and is fixed at its ends A and…

A: Free-body diagram of the shaft is given as, On using torque equilibrium condition,…

Q: For the stepped bar, determine the maximum bending stress (in MPa). Express your response using…

A:

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: 1- For the tapered bar shown with cross sectional areas A-0.02 m² and A 0.01 m² at each end. The bar…

A: In the question load is 4500N but in the diagram given load is 4000N , So I am solving with 4000…

Q: If M=2.5kip.ft, determine the magnitute of the resultant force the bending stresses produce on the…

A:

Q: FI5-1. Determine the minimum dimensicon a to the nearest mm of the beam's cross section to safely…

A: Given: The maximum allowable normal stress, σall = 10 MPa The maximum allowable shear stress, τall =…

Q: The copper shaft is subjected to the axial loads shown. Determine the displacement of end A with…

A:

Q: The bar is subjected to a moment of M = 100 N # m. Determine the maximum bending stress in the bar…

A: Given Moment = 100 Nm D = 80 mm = 0.08 m d = 20 mm = 0.02 m t = 10 mm = 0.01 m r = 10 mm = 0.01 m To…

Q: I1-55. If the beam is subjected to an internal moment of M - 30KN - m, determine the resultant force…

A: The internal moment subjected to the beam M=30 kN·m Width of the top flange of the beam b1=100  mm…

Q: Determine its smallest diameter d if the allowable bending stress is oallow = 130 MPa (Figure 1)…

A: Given data as per question Allowable stress =130 Mpa Distance between point A and B =3 m UDL applied…