11 .625 .125 SECTION A-A VIEW B-B .344 1.000 .313- 0.2407+.0013 -.0013 10 .125 8 B A Q 3.875 NO PAINT -2X-24UNF-2B 2.938

Q: 1. The clasticity of polymers and rubbers is caused by... 2. For stresses beyond the elastic limit,…

A: Since you have put a multi-part question that contains more than three sub-questions, thus we can…

Q: rigid body consisting of a sphere (mass m, radius r) and cylindrical wheel (mass m, radius r) and wo…

A:

Q: ?What does line 1 in the Figure below shows Critical Pt Linel X=09 Saturated Vapour Line Saturated…

A:

Q: 2. Determine the angular acceleration of each of the disks in Figure 2. 4 kg-m? 4 kg-m? 60 cm 60 cm…

A:

Q: Moment about

A: (a) Draw a free-body diagram of the member.     Write the expression of moment about point O.…

Q: .A car and its load weighs 40 kN and the center of gravity is 600 mm from the ground and midway…

A: GIVEN:W=40KNdistance between the rear wheel and front wheel =3m

Q: N Mi4 D 3- O 314 2 314 DIA, C'BOREX DE 2 HOLES

A: Given Data : 2D Drawing

Q: A fireworks show is choreographed to have two shells cross paths at a height of 103 ft and explode…

A:

Q: With respect to coordinate axes x and y, locate the centroid of the shaded area in the figure, also…

A:

Q: The square bar shown (Figure 1) is 70 mm thick and 5.4 m long and is fixed supported at both ends. A…

A: Given: Thickness of bar = 70mm Length, L2 = 3.3 m Change in length of L2 = delta = 0.13 mm Youngs…

Q: Figure shows a tie bar made of steel. When bolted between A and B double brackets, it is to be…

A: Given Data, P= Tensile load in the bar = 100 KN The bolt is of double brackets, so the shear load…

Q: What are limits or limits of size?

A: This question belongs to Metrology. Metrology is a science of measurement by using different…

Q: In your first week of the job, your boss has asked you to create a rigging solution for the mines.…

A:

Q: Part Three: In the diagram at the right, ABC represents a post-beam system rotating about an axis…

A:

Q: In the truss system shown, Calculate all internal forces in 3 m each member by method of joints.…

A:

Q: The steel structure (E=200GPA) shown in Figure Q4, is consisted of the solid bar, DC (length, L of…

A:

Q: Match the parts of a print to the terms below.

A: Choice H is the Scale of the drawing of the part on the print sheet.

Q: An inverted cone is placed in a water tank as shown below. If the weight of the cone is 46 N, what…

A: Given: Weight of the cone (W)=46N Assumption: Density of water (ρ)=1000kg/m3Acceleration due to…

Q: Provide the following views.

A:

Q: Begin a full-size layout of a pair of spur gears having a 4:1 velocity ratio, a 10-in center…

A:

Q: ct one: a. moderate and lowest b. highest

A: GIVEN:

Q: A 9 cm diameter solid aluminum post is subjected to a horizontal force of V= 7.8 kN and a…

A:

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: Prob 2. Find the mass of air in a closed chamber measuring 35 ft x 20 ft x 10 ft, when the pressure…

A: Given data- dimension of the closed chamber = 35 ft * 20 ft * 10 ft Pressure (P) = 17 lb/in2…

Q: Please help with these questions.

A: Absolutely! To read a vernier micrometer:Summary:The reading on the micrometer is approximately…

Q: 1. Consider a simple ideal Rankine cycle with fixed turbine inlet temperature and condenser…

A: Pump work input (c) remains the same  Turbine work output(a) increases  Heat supplied (b) decreases…

Q: A tensile test specimen of stainless steel alloy having a diameter of 0.495 in. and a gage length of…

A: Tensile test  Tensile testing is a sort of tension testing and a destructive engineering and…

Q: The accessory drive unit of a large aircraft engine involves an identical pair of 20 degree…

A:

Q: Each wheel of a four-wheeled rear engine automobile has a moment of inertia of 2.4 kg.m² and an…

A: To find: The Limiting speed of the vehicle around a curve. Given: The Moment of inertia of wheel is…

Q: The four bar mechanism shown in the figure (Given: OA = 4 cm; AB = 5 cm; BC 6 cm; OC = 8 cm) is a A…

A:

Q: Determine the name of the device and

A: Given; Moist air at 350 CRelative humidity is entering a psychometric deviceand leaving at,…

Q: Figure below shows two bearing supporting a 1000 rpm shaft and gear. The bearing on the left carries…

A:

Q: Please help me with this question. Thankyou very much!

A: Step 1: Step 2: Step 3: Step 4:

Q: What is streamline?

A:

Q: A No. 204 radial-contact ball bearing is used in an application considered to be light-to- moderate…

A:

Q: 20 In wire drawing process, the cross sectional area of wire is reduced. Select one: True False

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.