10m Do 0.30 m in the composite body shown, the identical thin disks are attached to a slender rod with m=2 kg. The disks are made rom material with mass per unit are of 20 kg/m2. Determine the mass moment of inertia of the composite body about in axis perpendicular to the page and passing through point O. A: -6.85?10?1 kg?m² B: 6.60?10?1 kg?m²

10m Do 0.30 m in the composite body shown, the identical thin disks are attached to a slender rod with m=2 kg. The disks are made rom material with mass per unit are of 20 kg/m2. Determine the mass moment of inertia of the composite body about in axis perpendicular to the page and passing through point O. A: -6.85?10?1 kg?m² B: 6.60?10?1 kg?m²

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Wire BC has a diameter of 0.10 in. And its material has the stress-strain characteristics shown in the figure. Determine the vertical displacement of the handle D if the pull on the handle is slowly increased and reaches the magnitude of P = 655 lb. o (ksi) 40 pulg 80 70 B 50 pulg - 30 pulg € (pulg/pulg) 0.007 0.12
Determine the moment of inertia (in4) ĪY of the area shown with respect to the vertical line that passes to the centroid of the composite area if b = 5.8 in, h = 0.71 in, L = 7.49 in, and W = 0.77 in. Round off only on the final answer to expressed in 3 decimal places.
A composite assembly consisting of a steel [G = 80 GPa] core (2) connected by rigid plates at the ends of an aluminum [G = 28 GPa] tube (1) is shown. The cross-sectional dimensions of the assembly are shown in the second figure. Assume L = 340 mm, D1 = 53, d = 37 mm, d2 = 19 mm. If a torque of T = 1200 N-m is applied to the composite assembly, determine (a) the maximum shear stress in the aluminum tube and in the steel core. (b) the rotation angle of end B relative to end A. (1) T T B L (1) d2 di DI Answers: (a) Talum = i 53.839 MPa Tsteel i 891.026 MPa (b) PB - PA = i 0.02467 rad (2)
Determine the displacement of point A on the free end of the cantilever beam. Neglect the overlap between material 2 and material 3. 2 in- 12 in 6 in 11 ft. 10 in 4 in P = 1000 lbs A PL 3EI Material 1- E₁20,000 ksi Material 2- E₂ = 5,000 ksi Material 3- E₂ 10,000 ksi
An aluminum plate is subjected to uniform stress along its boundaries, as shown in the figure. Determine the change of length of diagonal BD. 120mm 120 MPa 160mm , 100мра C 240 MPa E=80GPa ✓=0.3 G=30GPa Answer = -0.5888mm
3 The piece of plastic is originally rectangular. Calculate the shear strain Yxy at corners A and B if the plastic distorts as shown by the dashed lines. 2 mm 300 mm 2 mm D -400 mm- mm, B A 4 mm 72 mm 3 mm X
Q1: The beam shown in Figure 1 is subjected to a vertical force Pv and a horizontal force Ph. The data for Pv, Ph, a,L,and e are shown in Table 1. Determine the maximum compressive and tensile stresses under the vertical force (at a distance a from the left support.) Pv = 80k N a = G0o 6 omm e %3D 26 K N 120 mm L =3600 mm Figure 1 250 mm
The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 400 N is applied to it, determine the change in its length and the change in its diameter. E = 3.20 GPa, v = 0.4. %3D 400 N 400 N 200 mm
A square beam, 90 mm x 90 mm and 1 m long, simply supported at it ends is subjected to a uniformly distributed load of 60 kg/m over its span. Consider a polymer reinforced with silicon carbide fibers, with a fiber volume ratio of x = 10%. 4.1 Calculate the maximum deflection of the beam if the matrix material is acetal? 4.2 Determine the deflection of the beam if steel was used, for the same beam dimensions. 4.3 Determine the fiber volume ratio required to produce the same deflection as the steel beam?
Bar ABC is rigid and rotates freely about B. The loads consist of a point load and a uniform temperature change in both bars CD and EF. Determine the temperature change (AT) at which points A and E first come into contact. Report your answer rounded to the nearest degree. 100 in initial gap = 0.11 in F T E A = 2.0 in² AEF EEF = 12,000 ksi aEF LEF 100 in = 13.5 x 10-6 1/°F = 50 in B 14 k 100 in D с ACD= 1.5 in² ECD CD= 6.5 x 10-6 1/°F = 29,000 ksi = 150 in LCD Y Z
a. Determine the centroid of the composite figure.b. Calculate the moment of inertia with respect to the red horizontal axis.c. Calculate the moment of inertia with respect to the red vertical axis. given : L5 = 6 L6 = 4 L7 = 6
Bar ABC has an outer diameter of 10 mm and is made of red brass for which E = 100 GPa. Section AB is hollow with a wall thickness of 2 mm and section BC is solid. Knowing that P is 24 kN, applied to both sides of the bar at B and Q is 8 kN, applied to the bar at C as shown. What is the total %3D change in length of bar ABC? Express your answer in mm, to the nearest 0.01 mm, taking elongation as positive and contraction as negative. 4 13 'A В C P 400 mm -600 mm-