Required information A fabric used in air-inflated structures is subjected to a biaxial loading that results in normal stresses ox= 18 ksi and oz = 23 ksi. The properties of the fabric can be approximated as E = 12.6 × 106 psi and v= 0.34. 4 in. 3 in.

Required information A fabric used in air-inflated structures is subjected to a biaxial loading that results in normal stresses ox= 18 ksi and oz = 23 ksi. The properties of the fabric can be approximated as E = 12.6 × 106 psi and v= 0.34. 4 in. 3 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The sectional dimension of a reinforced concrete short column is b X h= 400 mm X 400 mm. The length…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: A vinyl [E = 2.80 GPa; v = 0.41] block with width b = 50 mm, depth d = 100 mm, and height h = 270 mm…

A: E = 2.8 GPa = 2.8 × 103 N/mm2Poisson's ratio (μ) = 0.41Determine the change in the depth dimension…

Q: The composite shaft, consisting of aluminum, copper, and steel sections, is subjected to the loading…

Q: 6. A three-block composite structure is loaded through rigid end plates, as s in the figure. What…

A: To find position of x such that end plates remain horizontal

Q: A composite beam is made of two brass [E = 110 GPa] bars bonded to two aluminum [E = 71 GPa] bars,…

A: Bending moment=260Nm a=10mm b=85mm c=20mm d=55mm

Q: 6. A three-block composite structure is loaded through rigid end plates, as shown in the figure.…

Q: The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner…

Q: An aluminum rectangular bar has a cross-section of 25 mm x 50 mm and a length of 500 mm. The Modulus…

Q: A 10.0 mm diameter cylindrical specimen of a bearing bronze material is pulled under uniaxial…

A: given-10.0 mm diameter 1500 N force∆d=0.67 mmn=0.35

Q: A closed right circular cylinder has radius 4 units and height 18 units A load of an unknown weight…

Q: 29. During laboratory testing of an 8-inch aluminum-alloy rod with a cross sectional area of…

A: Given:- The length of the aluminum-alloy rod during testing = 8 inch The cross-sectional area of…

Q: The column shown is made by filling a steel pipe with concrete. The concrete has an Elastic Modulus…

A: Solution-

Q: 7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses…

A: Given Data: The diameter of the solid aluminum cylinder is d1=3 in. The diameter of the steel tube…

Q: The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner…

A: Given data, D1 = 35 mm d1 = 20 mm G1 = 41 GPa D2 = 20 mm G2 = 80 GPa L = 430 mm T = 990 N-m To find…

Q: 10.4 A beam of the cross section shown is made of a steel which is opumed to be elastoplastic with E…

Q: A composite beam is constructed using a steel plate (14 mm x 125 mm) with two wood beams (75 mm x…

Q: steel pipe having a length of 2 m, an outside diameter of 0.25 m and a wall thickness of 16 mm, is…

Question

100%

Required information
A fabric used in air-inflated structures is subjected to a biaxial loading that results in normal stresses ox= 18 ksi and oz
= 23 ksi. The properties of the fabric can be approximated as E= 12.6 × 106 psi and v= 0.34.
4 in.
3 in.
Determine the change in length of side AB.
in.
The change in length of side AB is|

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

During laboratory testing of an 6-inch aluminum-alloy rod with a cross sectional area of 0.32in², a tensile load of 50,000 lbs.is applied. Ifthe cross sectional area decreases to 0.3188in? and lengthens to 6.022 inches, what is the Modulus of Elasticity and Poisson's Ratio? E = 6/ɛ V = = -E(lateral)/ɛ(axial)
Properties: Rod 1 8F D = 40 mm d = 20 mm L = 1.3 meter E = 80 Gpa ROD 1 ROD 2 Rod 2 D = 80 mm d = 20 mm L = 1.0 meters E = 80 Gpa 3F 2. The composite rod shown in the figure is composed of three rods rigidly welded together. Applied forces in terms of "F" are exerted in different parts of the composite rod. Compute the maximum safest value of "F" if the allowable total deformation of the composite rod is limited to 0.50 mm only. ROD 3 2F Rod 3 D = 60 mm d = 20 mm L = 1.2 meters E = 80 GPa 7F
The composite shaft shown in the figure consists of a bronze sleeve (1) securely bonded to an inner steel core (2). The bronze sleeve has an outside diameter of 25 mm, an inside diameter of 20 mm, and a shear modulus of G1 = 41 GPa. The solid steel core has a diameter of 20 mm and a shear modulus of G2 = 82 GPa. Assume L = 350 mm. The composite shaft is subjected to a torque of T = 910 N-m. Determine (a) the maximum shear stresses in the bronze sleeve and the steel core. (b) the rotation angle of end B relative to end A. T (1) (2) В
A prismatic aluminum bar has cross-sectional dimensions 40 x 60 mm and a length of 350 mm. The modulus of elasticity is 70 GPa and Poisson's ratio is u=0.35. When an axial load of 100 kN is applied, the proportional change in the bar's volume is
PROBLEM 4.75 A beam of the cross section shown is made of a steel that is assumed to be elastoplastic with E= 200 GPa and ay 350 MPa. For bending about the z axis, determine the bending moment and radius of curvature at which (a) yield first occurs, (b) the plastic zones at the top and bottom of the bar are 25 mm thick. 12.5 mm 60 mm 25 mm 60 mm 25 mm -12.5 mm
Determine the plastic moment Mp of the cross section shown when the beam is bent about a horizontal axis. Assume the material to be elastoplastic with a yield strength of 169 MPa. 5 mm t=5 mm 120 mm 5 mm 80 mm The plastic moment is kN.m.
Question 10 of 10 0/10 三 View Policies Show Attempt History Your answer is incorrect. Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.5 in.2 and an elastic modulus of 2400 ksi. Bar (2) has a cross-sectional area of 0.832 in.2 and an elastic modulus of 3110 ksi. Assume L1=16 in., L2-38 in., Q-8.2 kips, P=3.7 kips, and R=15.6 kips. Determine the horizontal deflection of end C relative to end A. R (1) (2) A B P L2 in. Answer: ucA = eTextbook and Media Attempts: 1 of 3 used Submit Answer Save for Later Last saved 2 minutes ago. Saved work will be auto-submitted on the due date. Auto- submission can take up to 10 minates. Using multiple attempts will impact your score. 5% soore reduction after attempt 1
A high-strength steel bar used in a large crane has a diameter d = 3.00 in. (see figure). Ⓡ The steel has a modulus of elasticity E = 29 x 105 psi and Poisson's ratio is y = 0.27. Because of clearance requirements, the diameter of the bar is limited to 3.002 in. when it is compressed by axial forces. What is the largest compressive load Pmax that i permitted? Assume that the material behaves linearly elastically. (Enter the magnitude in lb.) lb
The composite bar is subjected to a normal force P = 7500 lb as shown in the figure. The section of the composite bar is composed of two hollow tubes and a solid steel core. Determine the axial stress developed in each bar. Use Ecu = 18 x 106 psi, Est = 30 x 106 psi, and Ebr = 16 x 106 psi.
4 ft |←— 3 ft — Aluminum E = 10 x 106 psi W 6 ft- FIG. P2.96 6 ft Steel E = 29 × 100 psi 1.0 ft
A cylindrical bar of steel 9.9 mm (0.3898 in.) in diameter is to be deformed elastically by application of a force along the bar axis. Determine the force that will produce an elastic reduction of 3.0×10-3 mm (1.181 ×10-4 in.) in the diameter. For steel, values for the elastic modulus (E) and Poisson's ratio (v) are, respectively, 207 GPa and 0.30. i N
A vinyl [E = 2.65 GPa; v = 0.41] block with width b = 60 mm, depth d = 120 mm, and height h = 320 mm rests on a smooth rigid base. A load P is applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P= 180 kN is applied. Rigid plate Answer: Ad = i Width b P Depth d Height h Rigid base mm