10m 10m 4. An ideal Brayton cycle has a low and high pressure of 14.7 psia and 100 psia. The temperature of the air entering the turbine is 2000 R while the temperature of the air entering the compressor is 500R. Draw the PV and TS diagrams, find the heat added, Wc, Wt, Wnet, and efficiency. Btu Btu Btu ; 42.18% lbm 272.43 ; 87.52; 202.43 Btu; 114.91 lbm lbm lbm

10m 10m 4. An ideal Brayton cycle has a low and high pressure of 14.7 psia and 100 psia. The temperature of the air entering the turbine is 2000 R while the temperature of the air entering the compressor is 500R. Draw the PV and TS diagrams, find the heat added, Wc, Wt, Wnet, and efficiency. Btu Btu Btu ; 42.18% lbm 272.43 ; 87.52; 202.43 Btu; 114.91 lbm lbm lbm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a Rankine cycle, the pump takes in a saturated liquid at 100 kPa. The turbine inlet is 8 MPa and 600∘∘C. The turbine has an isentropic efficiency of 85%. a. Find the quality and temperature of the steam exiting the turbine. b. Find the thermal efficiency of the system. c. If the pump power is 50 kW, find the rate of heat addition to the boiler. d. If the cooling water may only change by 30∘∘C, find the required mass flow rate required.
At the beginning of compression, Otto cycle works on 0.2 lb/s of air at 14 psia and 1300F. The temperature at the completion of combustion is 45000R, the compression ratio is 5.5, and the hot-air standard is k = 1.3. a. Find V1 , P2 , T2 , P3 , V3 , T4b. Compute the heat added (QA),heat rejected (QR), work (W) andthe cycle efficiency (e).
1. An ideal air-standard diesel cycle with inlet conditions: 21.11˚C and 14.7 psia, 700 Btu/lbm heat input, and a compression ratio of 15. Find P2, T2, T3, V3, P4, T4, and the efficiency of the cycle. Take Note: Assume air standard values for R and k Cp = kR/k-1 Cv = R/k-1 a. Find the value of P2. (in psi or lb/in^2) b. Find the value of T2. (in Rankine) c. Find the value of T3. (in Rankine) d. Find the value of V3. (in ft^3/lbm) e. Find the value of P4. (in psi or lb/in^2) f. Find the value of T4. (in Rankine) g. Find the value of efficiency of the cycle. (ex. 100-%)
A diesel cycle with air as the working fluid has a compression ratio of 20. The temperature and pressure in the first process is 20°C, 95kPa and the highest attainable temperature is 1927°C. The air standard assumptions are applicable, both Kinetic and Potential energy are negligible. The mass/mass flow rate is negligible. Use the standard constants for air (Cp, Cy. R, and k). Determine the amount of heat transferred and rejected, the net work and thermal efficiency, and the mean effective pressure.
1. A reheat steam cycle has 13.65 MPa pressure at the high pressure turbine inlet and a 2500 kPa reheat pressure, the temperature at the inlet of the high pressure turbine and reheat temperature of the steam is 540 °C, condenser pressure is 3.4 kPa, engine efficiency of high pressure and low pressure turbine are both 75 %. Sketch the cycle lay out and cycle T-s diagram. a. Find the enthalpy at each state point. (Summarize) b. Find the actual enthalpy at the exit of the high-pressure turbine and low-pressure turbine. Find the cycle thermal efficiency С. d. If the net power at the turbine is 100 MW find the mass flow rate of steam, in kg/s; Heat rejected by the condenser, in MW е.
2. An electrical power plant that uses the Rankine cycle has a pump to increase the water pressure and multiply it by 50. In addition, there is a boiler whose fuel has a calorific value of 35 MJ/kg. The water that enters the process has a temperature of 60 °C and is at atmospheric pressure. The steam that leaves the turbine has a quality of 70% and the work generated in the turbine is 300 MW. a. How much water is needed to run the plant? b. What is its efficiency?
3- Air enters the compressor of a gas turbine at 120 kPa, 310 K. The air compressed to 1100 kPa, the turbine inlet temperature is 1460 K and the expansion occurs in two stages, with reheat to 1420 K between the stages at a pressure of 300 kPa. The compressor efficiency is 85 %. The net power developed is 2.2 MW. sketch T -S diagram then Determine: The thermal efficiency of the cycle. Qin Qin The back work ratio. Combustor Reheat combustor Turbine Turbine stage 1 stage 2 cycle Compressor
A simple Rankine cycles operate with an initial pressure of 1.69546 Mpa and 370.546oC temperature and exhaust to a heating system at 0.189546Mpa. Compute the turbine work, heat of steam generator, heat rejected, thermal cycle efficiency, and thermal engine efficiency. Draw schematic diagram and T-s diagram.
In a Brayton Cycle air enters the compressor at 101.32 kPa, 32 °C and leaves at a pressure of 808 kPaa. The air is heated to 717 °C in the combustor. For a net output of 2125 kW, compute: a) mass flow rate of air (kg/s), b) thermal efficiency of the cycle. use k = 1.4 for all problems
A rankine cycle with water superheats to 500.546oC at 3.1546 Mpa in the boiler and the condenser operates at 100.546oC. All the components are ideal except the turbine which has an exit state measured to be saturated vapor at 100.546oC. Find the cycle efficiency with a) an ideal turbine and b) the actual turbine. Draw the schematic diagram and T-s diagram.
1.) A Steam power plant operates using the ideal Rankine Cycle where steam initially enters the turbine at 5.0 MPa and 400C then after expanding, it condenses at 7 kPa and exits as saturated liquid. Draw the TS diagram, find the thermal efficiency, and steam rate.
1. Determine the Rankine efficiency of a condensing steam turbine operating in a Rankine cycle as follows: Steam pressure - 200 psiaSteam temperature - 1000 FExhaust pressure - 2 in Hg absoluteSteam rate - 1.5 lb/kW-hr 2. If the no. 1 problem has a thermal efficiency of 30%, how many barrels of 30 °API fuel oil will be required to produce 1000 kW-hr of power. Neglect the pump work.