1.7 A high-voltage direct-current (de) transmission line between Celilo, Oregon and Sylmar, California is operating at 800 kV and carrying 1800 A, as shown. Calculate the power (in megawatts) at the Oregon end of the line and state the direction of power flow. 1.8 kA Celilo, Sylmar, California 800 kV Oregon Answer: 1440 MW, Celilo to Sylmar

1.7 A high-voltage direct-current (de) transmission line between Celilo, Oregon and Sylmar, California is operating at 800 kV and carrying 1800 A, as shown. Calculate the power (in megawatts) at the Oregon end of the line and state the direction of power flow. 1.8 kA Celilo, Sylmar, California 800 kV Oregon Answer: 1440 MW, Celilo to Sylmar

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

My roll last two didgit are 75
power analysis systems / energy distribution The material used in the one-phase low voltage network given in Figure is copper (x=56m/Q.mm³). . Calculate the location and value of the largest voltage drop. 0,30 0,50 0,30 II 220 V 225 V 0,30 0,30 0,80 0,60 80 m x=56m/Q.mm? 60 m j=0,125A/m j=0,25A/m
Please solve it asap
Q) Why AC current is preferred over DC current for high power electrical circuits? NOTE: Answer must not exceed more than 5 lines
Power factor and power rating
Evaluate (130 points); Use 3 decimal places. 1. The annual load of a substation is given in the following table. During each month, the power is assumed constant at an average value. Find the (a) average load and (b) the annual load factor. Annual System Load January February March 8 Y 4 April May 26 2 6 2, Tv June 12 sing July 14 phas August 14 idea September 10 imp October 8 5Y5 November December 68 6 ma del
What is Per Unit System? In the given picture, would there be any difference in calculation of the transformers, if you choose primary or secondary side? Explain in words. 111kv 13-8 KV 13 8KV/5KV load 20MVA X= 8%. X-4%
The figure below shows a single phase power system with the following details. Generator G1: 12 kVA, 230 V; synchronous reactance Xs 5%; T2: 1.25 kV/230 V, 12 kVA, X-T, = 5%; Zline = 5%; T1: 240 V/1.2 kV, 10 kVA, XT, = 0.01+j0.2N. The load is consuming 8 Xs Zline eer G1 Zload kVA at 220 V at 0.8 lagging power factor. Using per unit calculations, draw the impedance diagram and find out the actual voltage at the terminal of the generetor G1. reler
In tan" tan M- M+ M OCT Evaluate (130 points); Use 3 decimal places. 1. The annual load of a substation is given in the following table. During each month, the power is assumed constant at an average value. Find the (a) average load and (b) the annual load factor. Annual System Load January 8 February 8 March 4 April 2 May 6 2, T- June 12 sing July 14 pha: August 14 idea September 10 imp October 8 5Y5 November 6 mac December 8 00 deliv
What if power is transmitted to everyone at 200 V instead of using a 9,000 V transmission line? By what factor would power loss increase? Assume the transformers DO NOT have power loss.
A 245-volt dc generator supplies power to a 15 KW load that is 100 meters away from the supply with a receiving end voltage of 230 volts due to feeder line loss. Then, another 10 KW load is connected in parallel across 15 KW load 90 meters farther with a receiving end voltage of 210 V. Include the circuit in your solution. Determine the efficiency of the transmission in percentage. Pout Use the efficiency formula: %n=Prnt+Posses x100% out
A high-voltage direct-current generating station delivers power to a city. The generator output voltage is V0 = 400 kV, the city is represented by resistance RL = 3918 ohms, and each wire of the transmission line round-trip between the station and city is represented by resistance RTL = 151 ohms. How much power (in mega watt) is lost along the transmission wire?