1.4 Determine the total compression of a bar made up of three circular cross-sections as shown in Fig. 1.70, the diameters being 10 mm, 20 mm and 30 mm of the top, middle and the bottom portions respectively. Take E, = 210 GPa, E, = 105 GPa and E = 100 GPa. 50 kN STEEL- 30 mm BRASS 20 mm COPPER 40 mm Fig. 1.70

1.4 Determine the total compression of a bar made up of three circular cross-sections as shown in Fig. 1.70, the diameters being 10 mm, 20 mm and 30 mm of the top, middle and the bottom portions respectively. Take E, = 210 GPa, E, = 105 GPa and E = 100 GPa. 50 kN STEEL- 30 mm BRASS 20 mm COPPER 40 mm Fig. 1.70

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

a) For the solid section shown in Figure Q1, determine dimensions a, b and c. b) Determine the centroid position (x, y) for the solid section shown in Figure Q1 relative to the origin O on the x-y axes. Clearly show the breakdown of the section into areas used in your calculations. y 85 mm 53 mm b 25 mm 157° 25 mm 65 mm Figure Q1 (Not to scale) X
The figure shows a cutaway view of an assembly in which a solid bronze [G = 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d1 = 1.65 in. The outside diameter of the tube is D2 = 3.6 in. and its wall thickness is t2 = 0.155 in. Overall dimensions of the assembly are a = 42 in. and b = 12 in. The allowable shear stresses for the bronze and aluminum materials are 9500 psi and 7800 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 4.9°. Based on these constraints, what is the maximum torque TB that can be applied at end B?
Choose five terms listed below. Then, define each and indicate its application. statics rigid bodies Force Vector Scalar Newton’s law of motion Vector resolution Static equilibrium Static equilibrium equations Internal & external forces Types of forces Free body diagram Principle of transmissibility Parallelogram law Triangle law Pythagorean theorem Law of sine
The figure shows a cutaway view of an assembly in which a solid bronze [G= 6,500 ksi] rod (1) is fitted inside of an aluminum alloy [G = 4,000 ksi] tube (2). The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at A. The rod diameter is d₁ = 1.55 in. The outside diameter of the tube is D₂ = 2.8 in. and its wall thickness is t₂ = 0.115 in. Overall dimensions of the assembly are a = 35 in. and b = 11 in. The allowable shear stresses for the bronze and aluminum materials are 9800 psi and 8500 psi, respectively. Further, the rotation angle of end B must be limited to a magnitude of 4.2°. Based on these constraints, what is the maximum torque Tg that can be applied at end B? Fixed End plate plate di TB Rod (1) D₂ Answer: TB = A Tube (2) a lb-in b B
In the truss system shown in the figure below, there are totally nine bars. Pick any six of them and calculate the forces they are bearing. Put your answers in the table below. Show your analysis. E Force Compression/ Bar magnitude Tension 4 m 45° АВ AC A 7 m AD 90 BD 3 m 90° CD CF B F CE 4 m 4 m DF 30 N FE
Example 21.18. A solid circular steel rod 6 mm in diameter and 500 mm long is rigidly fastened to the end of a square brass bar 25 mm on a side and 400 mm long, the geometric axis of the bars lying along the same line. An axial tensile force of 5 kN is applied at each of extreme ends. Determine the elongation of assembly. For steel E = 200 GPa and for brass E₁ = 90 GPa
A compound bar consisting of bronze, aluminum, and steel segments is loaded axially as shown in the figure. The cross-sectional area of the bronze, aluminum, and steel are 448 mm2, 622 mm2 , and 265 mm2 respectively.Determine the change in length (in mm) of the bar if P = 27199 N.The moduli of elasticity are 81.82 GPa for bronze ,73.92 GPafor aluminum , and 204.55 GPa for steel .
Calculate F3 in Ib so that the resultant of the forces is along the X axis F = 50 lb 25 F2 = 30 lb 23° 37° F3
Bar ABC is rigid and rotates freely about B. The loads consist of a point load and a uniform temperature change in both bars CD and EF. Determine the temperature change (AT) at which points A and E first come into contact. Report your answer rounded to the nearest degree. 100 in initial gap = 0.11 in F T E A = 2.0 in² AEF EEF = 12,000 ksi aEF LEF 100 in = 13.5 x 10-6 1/°F = 50 in B 14 k 100 in D с ACD= 1.5 in² ECD CD= 6.5 x 10-6 1/°F = 29,000 ksi = 150 in LCD Y Z
Part A In (Figure 1), r = 30 mm. Locate the centroid a of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. T = 0 mm Submit Previous Answers Correct Figure < 1 of 1 Part B Locate the centroid ī of the metal cross section. Neglect the thickness of the material and slight bends at the corners Express your answer to three significant figures and include the appropriate units. HẢ ? 150 mm = Value Units Submit Previous Answers Request Answer 50 mm 100 mm 100 mm 50 mm
i need the answer quickly