1.2 A pipe of 50 mm diameter and 45 m long is connected to a large tank, the entrance to the pipe being 3m below the surface. The lower end of the pipe which is 6 m below the upper end is joined to a horizontal pipe of 100 mm diameter and 75 m long which discharges to atmosphere. Calculate the discharge taking into account the sudden enlargement and entry losses: f = 0.008 for both pipes.

1.2 A pipe of 50 mm diameter and 45 m long is connected to a large tank, the entrance to the pipe being 3m below the surface. The lower end of the pipe which is 6 m below the upper end is joined to a horizontal pipe of 100 mm diameter and 75 m long which discharges to atmosphere. Calculate the discharge taking into account the sudden enlargement and entry losses: f = 0.008 for both pipes.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate the discharge through a pipe of diameter 200 mm when the difference of pressure head between the two ends of pipe 500 m apart is 4 m of water. Take f 0.009
Compute the Cross sectional area of Pipe Discahrge=0.8 m3/s Velocity=2 m/s
Water at 60F is flowing through a 3-inch inside diameter smooth horizontal pipe. If the Reynolds number is 353,000. Calculate the ratio of maximum velocity to average velocity. (1.18)
The distribution system requires to lift water to an area with an average elevation of 90 mamsl from the pumping station at 35 mamsl. The area has a demand requirement of 30 MLD and the minimum pressure head requirement is 20 m-head. The pipe which will serve the area is 500 mm with C-value of 90 and length of 3000 m. Determine the following: a) total head loss along the pipe in meter, b) the head of pump required in meter, and c) the power required by the pump with an efficiency of 80% in kilowatt. Note: Theaverage water surface level of the reservoir which supports the pumping station is 5 m.
in a given setup, distilled water at 75 degree f has been found to be transported through a one and a half diameter horizontally oriented galvanized iron pipe running 1500 feet with a given flow rate of 0.1 cubic feet per second. what is the pressure drop in the given length of pipe assuming that the friction factor is take as 0.023?
This is merely a past paper question please assist
A pitot tube with dia of 3cm is installed in a pipe with ID150 mm. Water flows through the pipe, and the determined pressure drop across the pitot tube is 45 kPa. What is the average velocity of the flow.
fast.
Find the difference in pressure head and velocity of flow of an ail through a pipe, when the difference of mercury level in a different U-tube manometer connected to the two tappings of the pitot tube as 116 mm. Take co-efficient of the pitot tube ("L shaped measuring instrument) as 0.97 and sp. gr of ail = 0.85 (Enter only the values in the boxes by considering units given in the bracket. Do not send the hand written answers to my mail Id) Difference in pressure head (unit in mm) = Velocity of flow (unit in km/hr)%3D
I need help with this question: Q. A sprinkler system pumps water through a large pipe inlet with a diameter (d1). The then breaks into N narrow Pipes (which have a diameter, d2, and a length, L2), before the water is released to the atmosphere, as shown in the figure. The entrance to the small pipe from the large pipe has a loss coefficient of KL. You may assume the flow is laminar and fully developed everywhere in the system, and that any changes in height are neglible. (The viscosity is NOT negligible) a) Find an expressin for the velocity of water leaving the sprinkler b) Find an Expression for the gauge pressure at point A, a distance L1 upstream of the narrow pipes. Express your answer in terms of the flowrate, Q. c) The inner diameter of the first segment of the pipe is d1 = 10mm, the inner diameter of the second set of pipes is d2 = 1mm, with N = 25. The flowrate through the sprinkler is Q = 0.2 L/s. Flow in pipes typically becomes turbulent when the Reynolds number exceeds…
Give answer soon please
piping system can be neglected but the minor loss at the exit can't be neglected. What is the total head loss in the system, i.e. free surface to pipe exit? What is the minor loss at the exit? volumetric flow rate at the exit is 0.01 m³/s. Assume the minor loss at the entrance of the The valve is partially open. The pipe is made of commercial steel (ɛ = 0.046 mm). The 4. Water is being discharged from a very large reservoir via the piping system shown below. What is the loss coefficient at the exit? Water p=1000 kg/m3 5 m p=0.001 kg/(m s) 0.1 m Q=0.01 m3/s 25m