1. Use two NOR gates to construct basic SR latch circuit shown in Figure 1. Connect R and S inputs to switches A and B respectively. DO NOT FORGET to connect Vcc and Ground pins of ICs you used. Connect and Q and Q' to the Logic Indicator. Realize the truth table according to the inputs in Table 1. What happens SR=11 goes to SR=00? Table 4.1 田 SRQ Q 0 0 0 1 |1 |1 1

Q: 1. Give the temperature classification for solid insulating materials. Why is this classification…

A: It is asked to give the temperature classification for solid insulating materials. Also we need to…

Q: NSTRUCTIONS: - Answer in this format: Given, Illustration, Required Conversion, Solution, Final…

A: Given Data: Illumination  E=150 meter-candle Area of the hall A=45 × 15 m2 The depreciation factor…

Q: An 8 m × 20 m poultry handling area is to be lighted at an averagé maintained footcandle of 50 fc…

A: It is given that: Area=8×20average maintained footcandle=50cu=0.38LLF=0.75

Q: With neat diagram explain the parts of galvanometer

A: The galvanometer is the device used for detecting the presence of small current and voltage or for…

Q: A half-wave rectifier has an input voltage of 240 V rms. If the step-down transformer has a turns…

A: we need to determine peak load voltage.

Q: A FET has lpss=4lp and gmo = 10mS then gm express answer in mS

A: FET: It is a semiconductor transistor known as field effect transistor. It works due to single…

Q: Briefly explain the working of following power plants a) Thermal Power plant b) Hydel power plant

A: thermal power Plant coverts heat energy to electric power / Energy. The basic principle of these…

Q: In a commercial building, the glazed area need not be greater than floor area for maximum daylight.…

A: Approach to solving the question: Answer the given question.

Q: Choose which answers are correct ‎‏What is the unit of slope of a Fuel cost curve ? a . $ / MWh b .…

A:

Q: what is error in mesurement system? Also discuss its types

A: Error is the difference between the true value and measured value of the system. Error = measured…

Q: How many nodes are there? image d.png ... 1.5 0 20 50 2 A( )5 A Answer _nodes

A:

Q: b 2000 CRO (14 1.00-1 CR₂) Jov w ML WW 10.0-2 CRE TA 0.00-2 CR4)

A:

Q: What information is contained in the specification K, 10,000

A: Kp stands for the position error constant for the step input function.  here, Kp = 10000

Q: 4)-What is HRC Fuse : Working & Its Applications. please answer not by hand

A: HRC Fuse: High rupturing capacity fuse or HRC fuse are fuses that carry a short circuit current for…

Q: The curent in a 0.05-H inductor is I= 42 – 30° A. If the frequency of the current is 60 Hz, what is…

A: The equation of the current in time domain is: I(t)=4cos(ωt-300)A The inductor value is L = 0.05H…

Q: 17. A 15 A, 125 V, 10 receptacle installed of a dwelling unit does not require GFCI protection. A.…

A: Solution of question (18): Four options are given in the question. We need to choose the correct…

Q: 9. What is the minimum ampacity of the wire that can be used for a 30A branch circuit?      a. 30A…

A:

Q: A 40 amp branch circuit is run a long distance requiring a voltage drop calculation which increases…

A: To determine the proper size for the copper equipment grounding conductor in a 40-amp branch…

Q: A 4 AWG copper electrode that's encased in concrete must be a minimum of _______ feet long. A. 20 B.…

A: According to the question we have discuss 4 AWG copper electrode that's encased in concrete must be…

Q: Skitch  a wire of installation

A: Sketch  a wire of installation

Q: Please answer in typing format

A: The Peltier effect is the result when electric current is passed between two materials,such that it…

Q: Suppose in an IC fabrication factory there is conveyer belt from which workers collect the ICs &…

A: The twisted ring counter will have 5 D-flip-flops with the initial state given as 01010 The…

Q: TOPIC: Power Systems, Power Plants & Illumination INSTRUCTIONS: - Answer in this format: Given,…

A: Given information is written below. The room dimension is l×w×h=20 m×10 m×5 m. Lamp is placed at the…

Q: Inverting Op-Amp R₁ R₁ Vo R2 R4 998.48m V R2 R3 9.9844 R1 R4 2.1244 out of phase A(gain) A(gain)…

A:

Q: The balanced system below has a phase voltage of 120 V. It supplies a balanced load coil that is…

A:

Q: What can you do in the sim

A: You can do several things in the sim is as follows;  1.You can recreate yourself and friends in the…

Q: In the circuit below I = 3245° mA. What is the KCL expression at node a following the %3D…

A:

Q: 5 - What should be done first when a person being electric shocked seen? A) Cut off the electricity…

A: If we seen person being electric shocked then we need to do take some necessary action

Q: The female terminals are typically located in which connector half? O Clip O Cap O Receptacle O Plug

A: Plug used to connect with the socket. The female connector is generally a receptacle that receives…

Q: You're installing an aluminum grounding electrode conductor that has an insulating jacket. Which of…

A: Aluminum grounding electrode conductor should not be used in direct contact with masonry or earth,…

Q: Printer circuit boards are functionally tested after being filled with semiconductor chips, One…

A:

Q: using the base of 2 to answer following subtraction:  1000 base 2 -101 base 2 ________________

A: According to the given question, it is required to determine the binary subtraction of the two given…

Q: 200 200 20 0.53

A:

Q: 5- An instrument is used for lowering the value of voltage for measuring and protection is a.…

A: The objective is to determine the correct option for the given statements.

Q: With the help of schematics, briefly describe, how a telephone set works.

A:

Q: The circuits branch is defined as: Select one: a. a single path in a network, composed of one source…

A: The circuits branch is defined as,

Q: Facts: You have learned the basics and fundamentals of Electronics. We could say that all of the…

A: These are three component which are used in every circuit 1. Capacitor 2.Resistor 3. Diode

Q: 5. Determine whetneo or not each of the following systems are i) yon) = >cCn) + n.xcn+1) (i) yen) =…

A: A system is BIBO-stable only if bounded-input always produces bounded output.

Wheatstone Bridge Method

A Wheatstone bridge is a circuit used to measure unknown resistance by measuring the ratios of the two branches of the circuit such that each branch has two resistance and out of four resistance one is unknown. The two branches are joined in between with the help of galvanometer which is used to determine the direction of the current. The main advantage of this circuit is that it can provide the most accurate measurement (different from a simple voltage separator).