1. Use only the Steam Table to answer this Item. A boiler (heat exchanger which operates under constant pressure process) produces saturated steam at 5 Mpaa converting all liquid from a feedwater pump with water temperature at 40 deg C and pressure = 5 Mpaa. For a steam flow rate of 10.69230 kg per second, find/draw the 2. a) PV and TS Diagrams on solution sheet 3. b) Work.

1. Use only the Steam Table to answer this Item. A boiler (heat exchanger which operates under constant pressure process) produces saturated steam at 5 Mpaa converting all liquid from a feedwater pump with water temperature at 40 deg C and pressure = 5 Mpaa. For a steam flow rate of 10.69230 kg per second, find/draw the 2. a) PV and TS Diagrams on solution sheet 3. b) Work.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

2. A geothermal power plant has the thermal energy at well head of 1,289 KJ, mass of the liquid of 82 kg, and specific enthalpy at final stage of 4.12 KJ/KG, what is the value of work at the heat utilization system of the plant?
A reversible engine receives heat from a source at 800 ° C some heat goes to a sink at a temperature of 25 ° C. If the motor receives a heat flow of 1200 kJ / min find: a) The thermal efficiency of the motor and b) The working power output of the motor are in kW. Ans: a)η=72.2% b)Ẇ=14.44kW
An ideal regenerative cycle is executed with steam generated at 8 MPa, 500 degrees Celcius. Before condensing at 0.014 MPa, steam is extracted for feedwater heating at 0.8MPa. Find: a) Ideal work of the turbine b) turbine thermal efficiency c) cycle thermal efficiency d) draw the actual Ts diagram
a) A reversible heat pump absorbs heat at a temperature of 35.00oC and produces heat at 67.00oC, The work input rate is 101.00 kW, determine the heat output rate. the answer is 1073.13kW b) A reversible heat pump absorbs heat at a temperature of 25.00oC and produces heat at 61.00oC, The work input rate is 110.00 kW, determine the heat input rate. the answer is 2490.16kW
The air entering a compressor with a pressure ratio of 10 at 100kPa at 27°C leaves at 600K. It enters the turbine at a temperature of 1300 K and exits at a temperature of 800 K. Since the power of the gas turbine is 10 MW, a) Draw the T-s diagram of the cycle b) Find the amount of fluid circulating in the installation. c) Find the adiabatic efficiencies of the gas turbine and the compressor. d) Find net work Note. Assume that the specific heat of heating of the air is constant. cp=1 kj/kgC cv=07181 kj/kgC
Air undergoes Isothermal expansion in a Carnot cycle where the pressure. decreases from 2.5 MPa to 1.5 MPa. This process has a temperature of 550 K and it decreases to 400 K before the Isothermal compression stroke. Find a.) Qa, b.) Qr, c.) Whet (kJ/kg), d.) the efficiency (%), e) draw the T-S diagram with proper label of points, and f.) the pressures before and after Isothermal compression
15
Thermodynamics Clear writing, please ?
Thermodynamics
Question 2 A refrigeration cycle operates with R-134a. State 1 State 2 TA 15 psia 180 psia Saturated liquid 0 °F 200 °F QH If QL flow rate m, the work in Win, the compressor efficiency 7., and the volumetric flow rate V. 144,000 Btu/hr, find the COP, the mass %3D Win m = %3D 4° 4. Saturated vapor Win =
The compression ratio in a gasoline engine is 8. The total cylinder volume of the engine (for the bottom dead point) is 600 ml, and air enters the cylinders at a temperature of 20 ° C and a pressure of 100 kPa andThe maximum temperature of the cycle is known as 1500 ° C. a) Calculate the heat input in the cycle in kJ. b) Calculate the thermal efficiency of the cycle c) Calculate the power generated in the cycle.