Answered: c) A power station has an output of…

c) A power station has an output of 2000MW and its thermal efficiency is 25%. Determine the amount of power loss and the coal consumed in tonne/hr if the calorific value of coal is 30 MJ/kg.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The power generated by an adiabatic steam turbine is 5MW, when the steam enters the turbine at a pressure of 2.3MPa, a temperature of 400C and a speed of 50m/s; and leaves the turbine at a pressure of 15kPa, a quality of 90% and a speed of 180 m/s a) Represent the process on a P-V diagram. b) Find the mass flow rate of the steam. c) Find the exit area of the turbine.
If a piston-cylinder system has V = 0.8m^3 of saturated water vapor at P1 = 250 kPa, at which the piston is sitting on a number of stops. The heat is slowly transferred to steam until the piston begins to move off of the stops at a pressure of P2 = 300 kPa, the heat transfer to steam continues until the volume doubles. a) draw the control volume, with assumed direction of work and heat transfers b) draw P-v diagram c) find final temperature
a) A reversible heat pump absorbs heat at a temperature of 35.00oC and produces heat at 67.00oC, The work input rate is 101.00 kW, determine the heat output rate. the answer is 1073.13kW b) A reversible heat pump absorbs heat at a temperature of 25.00oC and produces heat at 61.00oC, The work input rate is 110.00 kW, determine the heat input rate. the answer is 2490.16kW
A) Steam enters a turbine at a pressure of 30 bars, temperature of 400 degrees Celsius and exits at a pressure of 1bar. The turbine is isentropic, how much power is produced per unit mass flow rate, w. Their is no change in kinetic or potential energy and no heat transfer. Answer in kJ/kg B) Steam enters a turbine at a pressure of 30 bars, temperature of 400 degrees celsius and exits at a pressure of 1bar. If the turbine is operating at 95% isentropic efficiency, how much power is being produced per unit mass flow rate, w. Their is no change in kinetic or potential energy and no heat transfer. Answer in kJ/kg C) Steam enters a turbine at a pressure of 30 bars, temperature of 400 degrees celsius and exits at a pressure of 1 bar. If the turbine at 95% isentropic efficiency, what is the quality of the steam exiting the turbine? Their is no change in kinetic or potential energy and no heat transfer.
1) Air is compressed under Constant Entropy Process from 10 Psia, 3 ft3, 90°F to 50 Psia. Find the following: a) Final volume in ft3. b) Final temperature in °F. c) Work non-flow in BTU. 2) From problem #1 Use all PVT values, What if the 1lbm of air is compressed under quasi-static process (n=1.27). Find the following: a) Work non-flow in BTU. b) Heat in BTU. Please answer only number 2.
1d) A house has an electric resistance heater with an efficiency of 95%. The house is in a cold climate with heating requirement of 120 million BTU/year and no need for air conditioning in the summer. If a 14 costs $10700, what heat pump with an HSPF is the payback time in years (2 significant digits) for the heating savings compared to keeping the current resistance heater assuming electricity costs of $0.12/kWh?
b) Determine the energy transport rate for the system shown in Figure below. Fuel flow Top heat loss Exhaust flow Epuet15,000 Btu/min Eethaut500, Btu/min 180,000 Btu/h System boundary Engine-generator set 200. hp Bottom heat loss 54,000 Btu/h 50.0 hp Electrical workout
A pneumatic cylinder moves a box on an assembly line by 2 ft by applying a continuous force of F= 275 Ibf for 0.5 seconds. a. How much work was done by the cylinder? W =. b. What was the power output? P =. c. If 1 hp = 550 ft.lb/s, express the power output in horsepower: HP =
a) A refrigeration cycle is chosen to maintain a freezer compartment at 10.0°F in a room that is at 90.0°F. If 200. Btu/min are extracted from the freezer compartment by heat transfer and the freezer is driven by a 1.00 hp electric motor, determine the dimensionless coefficient of performance (COP)of the unit, defined as the cooling rate divided by the input power. b) Determine the energy transport rate for the system shown in Figure below. Fuel flow Top heat loss Exhaust flow Epuet=15,000 Btu/min 180,000 Btu/h Ecshaut =500. Btu/min System boundary Engine-generator set 200. hp Bottom heat loss 54,000 Btu/h 50.0 hp Electrical workout
The compression ratio in a gasoline engine is 8. The total cylinder volume of the engine (for the bottom dead point) is 600 ml, and air enters the cylinders at a temperature of 20 ° C and a pressure of 100 kPa andThe maximum temperature of the cycle is known as 1500 ° C. a) Calculate the heat input in the cycle in kJ. b) Calculate the thermal efficiency of the cycle c) Calculate the power generated in the cycle.
Q2. From the following figure; 400 power, kw L 200 0 12 8 Time, hr 1. 2. What will be the highest power value for this project? ( What will be the total rated output? (