1. Two parallel shafts are connected by pure rolling contact. The diameter of the smaller cylinder is 20cm, and the speed ratio is given as 2.75. Determine the diameter of the other cylinder, and the center-to-center distance if (a) they are turning in the same direction, and (b) they are turning in the opposite direction.

1. Two parallel shafts are connected by pure rolling contact. The diameter of the smaller cylinder is 20cm, and the speed ratio is given as 2.75. Determine the diameter of the other cylinder, and the center-to-center distance if (a) they are turning in the same direction, and (b) they are turning in the opposite direction.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Find the distance in (inches) of the shafts if the small cylinder is 88 inches in diameter. The two…

A: To find: The distance of the shaft. Given: The diameter of smaller cylinder is d1=88 in. The speed…

Q: S3 Ts4 uniform spe T= 81 it shafi E rotates at a

Q: Two parallel shafts, 61 cm apart and having a speed ratio of 3, are connected by cylinders in pure…

Q: The gear 'A' and gear B' are tried to transmit power from one shaft to another shaft. The gear 'A'…

A: Let us discuss about power transmission between shaft A and shaft B. Given data, Gear A, Tooth space…

Q: have already asked this question twice. Please only answer this problem if you can answer explicitly…

Q: (a) The direction of the torque in the gear train can be determined using. (b) When the input and…

A: Answer: Torque and energy balance Reverted gear train Perpendicular Intake stroke

Q: speed, Wh

Q: A lathe is capable of spinning a cylindrical solid aluminium bar of radius 2.4 cm and length 75 cm…

Q: Two shafts, having axes in the same plane intersecting at an angle of 45 degrees, turn in opposite…

Q: Determine the brake horsepower of a round steel shaft with a torque of 17.5 in-lb running at 1800…

Q: Which of the following does Newton's first law of motion describe?

A: Option (a) Inertia is correct option

Q: 3. In a reverted gear train, as shown in Fig. 13.32, two shafts A and B are in the same straight…

Q: ) Indicate the direction of all force components of worm and worm ear. 斗 2.

Q: Consider the gear/pulley mechanism shown below (top view). The gear on the lower left is driven at a…

Q: le a reverted train Fig. (1), An arm A Carries two concentric separate wheels B and C a compound…

Q: meter. ler A:B:C has a speed ratio of 3:2:4 are externall ter distance between cylinder A and C is…

Q: In an epicyclical gear train of the sun and planet, the pitch circle diameter of the internally…

Q: A two-step power transmission with two identical gear sets (pinions and output gears) is designed to…

Q: answer 12

A: The sum of the length of the shortest and the longest of a planar quadrilateral linkage if less than…

Q: In a reverted gear train, as shown in Fig. 13.32, two shafts A and B are in the same straight line…

A: Given data as below:mA=2 mmmB=4.5 mmNA=12*NBTmin=16To determine·Number of teeth on each…

Q: (10) The lead screw of a lathe has a 2.0-in Acme thread, 2½TPI. To drive the tool carriage, this…

A: Answer: (a) The efficiency of the screw & the collar: 16.3435% (b) The power to drive the screw:…

Q: The machine design has stated that a 2.5 kW electric motor with an input speed of 1000 RPM is needed…

A: Given Data The power of the electric motor is: P=2.5 kW The input speed is: N=1000 RPM Th overall…

Q: 4) The criterion of constraints for a kinematic chain having plane motion is given by the equation:

Q: 5. A rolling cone with a center angle of 15⁰ turning at 240 rpm makes external contact with the…

A: Given Data

Q: 1.Power is to be transmitted from one shaft to another which is parallel. The shafts are 9 inches…

Q: A 2 inch solid shaft is driven by a 37 in. gear and transmits power at 120 rpm. If allowable…

Q: A lathe is capable of spinning a cylindrical solid aluminium bar of radius 2.4 cm and length 75 cm…

A: Given data Radius of solid aluminum bar = 2.4 cmIn 1.3 seconds, it reaches an angular speed of 12000…

Q: Two shafts, having axes in the same plate intersecting at an angle of 40°, turn in the same senses…

Q: The approximate distance between the two parallel shafts is 1500 mm. The shafts are to be connected…

Q: (b) What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s…

Q: ke angle is 0°. The minimum value of sh

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

1. Two parallel shafts are connected by pure rolling
contact. The diameter of the smaller cylinder is 20cm,
and the speed ratio is given as 2.75. Determine the
diameter of the other cylinder, and the center-to-center
distance if (a) they are turning in the same direction, and
(b) they are turning in the opposite direction.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Raw material with an input speed of 3.1 MIS will be rolled to the rolling mill with a plate-shaped cross-section of 155 mm2. Orünün since its cross-section is 96 mm2, what happens to the output speed of the product from the roling mill as mis? Please select one: A.8 B.5 C.11 D.10 E.15
ANSWER NO. 8 ONLY
Two parallel shafts, 61 cm apart and having a speed ratio of 3, are connected by cylinders in pure rolling contact. Determine the D2 in cm, when they turn in opposite directions.
7. The outside diameter of a hollow shat is 1.6 times the inside diameter. When transmitting 420 W of power at 180 rpm, the angle of twist is one degree over a length of 40 times the inside diameter. Taking G for the material as 85 GN/m?, determine the outside diameter of the hollow shaft in mm.
Correct Solution need.. Two parallel shafts, 61 cm apart and having a speed ratio of 3, are connected by cylinders in pure rolling contact. Determine the D1 in cm, when they turn in same directions.
A 60 mm power screw has triple square threads with a pitch of 6 mm and a friction angle of 4o.Neglecting the collar friction: a) Determine the efficiency of the screw. b) Is it possible to lower the load at constant speed? explain why?
An epicyclic gear consists of ring gear, planet gear and sun gear. The ring has 72 internal teeth and sun gear has 32 external teeth . Planet gear meshes with both ring and sun gears and carried an arm which rotates about the centre of the ring gear at 20 r.p.m . If the gear A is fixed. Calculate the speed of planet gear.
3. In a reverted gear train, as shown in Fig. 13.32, two shafts A and B are in the same straight line and are geared together through an interme- diate parallel shaft C. The gears connecting the shafts A and C have a module of 2 mm and those connecting the shafts C and B have a module of 4.5 mm. The speed of shaft A is to be about but greater than 12 times the speed of shaft B, and the ratio at each reduction is same. Find suitable number of teeth for gears. The number of teeth of cach gear is to be a minimum but not less than 16. Also find the exact velocity ratio and the distance of shaft C from A and B. 2 4 [Ans. 36, 126, 16, 56; 12.25; 162 mm] Fie. 13 32 B.
ANSWER NO. 5 ONLY
An 54 tooth spur gear transmits a torque of 15000N.mm. The pitch circle diameter is 150 mm, and the pressure angle is 20o. What is most likely the radial force on the gear? 73 N 42 N 31 N 64 N
ANSWER NO. 11 ONLY
A gear box has an input speed of 1,809 rev/min clockwise and an output speed of 475 rev/min anticlockwise. The input power is 49 kW and the efficiency is 0.77. Determine the input output Power in kW