1. The simplified schematic diagram below illustrates the principle of the ordinary toilet tank filling system. The ball floats on the water. As the ball gets closer to the top of the container, the stopper decreases the flow of water. When the container becomes full, the stopper shuts off the flow of water. Draw a block diagram for the water-filling system. Pulleys- Cord Stopper Water Water Ball Float Container Stopcock

1. The simplified schematic diagram below illustrates the principle of the ordinary toilet tank filling system. The ball floats on the water. As the ball gets closer to the top of the container, the stopper decreases the flow of water. When the container becomes full, the stopper shuts off the flow of water. Draw a block diagram for the water-filling system. Pulleys- Cord Stopper Water Water Ball Float Container Stopcock

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A pump station design fills a pressurized water tank by pumping water from a reservoir. The flow rate is 0.75 cfs. The pump is 10 feet above the reservoir, and the water tank is 100 ft above the pump. The pressure in the water tank is 10 psi. The suction and discharge lines are both (actual diameter) 6-inch Sch 40 steel (pipe roughness = 0.00015 ft). Use a kinematic viscosity of 1.21 x 10-5 ft²/s. Total pipe length is 200 ft. The suction line is 10 ft. You must account for friction loss, but you can neglect the minor losses. a. What is the head added by the pump in ft? b. What is the power added by the pump in HP (recall 1 HP = 550 ft*lb/s)? 110 ft 10 ft 0 ft
Question 4 of 13 -/8 View Policies Current Attempt in Progress Three liquids that will not mix are poured into a cylindrical container. The volumes and densities of the liquids are 0.607 L, 2.60 g/cm³; 1.13 L, 1.18 g/cm3; and 0.357 L, 0.634 g/cm3. What is the force on the bottom of the container due to these liquids? One liter = 1L = 1000 cm?. (Ignore the contribution due to the atmosphere.) Number i Units I!
(b) Your company bought a venturi meter to measure water flow rate in one of the closed systems in your plant. The only place where this venturi can be attached to that system is by putting the venturi meter at 30-degree angles, as shown-an inverted U-tube manometer than been linked to that venturi meter because of space constraints at the lower part of the system. You need to make a complete report on the calculation and analysis of the water flow rate. You decided to start your study by creating a flow rate equation for this system, starting from the Bernoulli equation to make your statement clear. After deriving the flow rate equation, you determine the exact water flow rate for the system. Show what your report looks will be. Oil (SG = 0.85) 30 Diameter = 0.1 m Diameter = 0.3 m
Q5: The compartments (B) 4 Cc) in figure below are closed & filled with air. When the gauges (A) f (D) read as indicated, what should be the value of Cx) for gaug eCE)? (Mercury in each U-tube gauge) 2.07 bar B 254 Air D Air E
please answer the questions below the drawing
Show all working explaining detailly each step
PLEASE ANSWER D E F THANK YOU
Describe about the Smooth-drum vibrators.
Describe about The Pressuremeter.
A 4m Oil (0.90) 3.75 mm B Mercury (13.57) This vertical pipeline with attached gage and manometer contains oil and mercury as shown. The manometer is open to the atmosphere. There is no flow in the pipe. Express the pressure reading at A in bar. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: bar Decimal Places required in the final answer: 3
Need only handwritten solution only (not typed one).
The 250-ft-long hose is made of a material having a roughness of e=0.0005 ft. (Figure 1) Figure 80 ft Part A Determine the power the pump must supply in order to discharge 45 ft³/min Express your answer using three significant figures. -9.583 W₂= Submit A vec Provide Feedback 6 Previous Answers Request Answer * Incorrect; Try Again; 4 attempts remaining ? Review f water at T = 60°F at from the 3-in.-diameter hose. hp Next >