1. The section of a column is shown in figure: For this problem, b₁ = 300 mm, b₂ = 180 mm, d₁ = 250 mm, and d₂ = 350 mm. fc' = 28 MPa, and fy = 414 MPa. 4-28 mm 34 mm d₂ a) Determine the location of the centroid of the gross concrete measured from the y-axis. b) Determine the location of the plastic centroid of the column measured from the y-axis. Consider the displaced concrete occupied by the steel.

1. The section of a column is shown in figure: For this problem, b₁ = 300 mm, b₂ = 180 mm, d₁ = 250 mm, and d₂ = 350 mm. fc' = 28 MPa, and fy = 414 MPa. 4-28 mm 34 mm d₂ a) Determine the location of the centroid of the gross concrete measured from the y-axis. b) Determine the location of the plastic centroid of the column measured from the y-axis. Consider the displaced concrete occupied by the steel.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The composite bar is subjected to a normal force P = 7500 lb as shown in the figure. The section of the composite bar is composed of two hollow tubes and a solid steel core. Determine the axial stress developed in each bar. Use Ecu = 18 x 106 psi, Est = 30 x 106 psi, and Ebr = 16 x 106 psi.
d C
I. Problem Solving: Answer what is being required. Show you complete solution. 1. Compression test was applied to a certain type of wood. Compute the stress based on the following dimensions. The grains are parallel with the length. а. Dimension (mm) Load (N) Compressive stress (МРa) Compression Test L = 50 Parallel to the grain B = 75 130,000 W = 75 L = 50 Perpendicular to the B= 75 W = 75 35,000 Grain b. What would be the shear stress for a single shear for the same data in a.? c. What is the modulus of rupture if the width of the specimen is 50mm, depth is
A vinyl [E = 2.65 GPa; v = 0.41] block with width b = 60 mm, depth d = 120 mm, and height h = 320 mm rests on a smooth rigid base. A load P is applied to a rigid plate that rests on top of the block. Calculate the change in the depth dimension d of the block after a load of P= 180 kN is applied. Rigid plate Answer: Ad = i Width b P Depth d Height h Rigid base mm
Situation 5: The compound bar, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/*C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segrnent 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10- 200 - 500 mm→- 400 mm- 800 mm Aluminum Steel Bronze 17. Compute the stress in the bronze bar a. 31.6 MPa (T) b. 31.6 MPа (С) 18. Compute the stress in the aluminum bar. а. 45.1 MPа (Т) b. 45.1 MPa (C) 19. Compute the stress in the steel bar. 79.0MPA (T) 79.0MPA (C) 13.6 MPa (T) 13.6 MPa (C) c. d. 54.1 MPа (Т) 54.1 MPa (C) с. d. a. C. 97.0 MPa (T) b. d. 97.0 MPa (C)
Required information For the concrete beam shown, the modulus of elasticity is 25 GPa for the concrete and 200 GPa for the steel. Take b=218 mm and d = 450 mm. Use an allowable stress of 12.5 MPa for the concrete and 140 MPa for the steel. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Using the area of steel calculated in part a, determine the largest allowable bending moment. The largest allowable bending moment is 96.06 kN-m.
2. The compound bar given in figure, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25 °C. Assume that the walls do not yield and use the following data: A (mm?) a (1°C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segment 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10-6 200 800 mm 500 mm– +400 mm→ Aluminum Steel Bronze
Plz
SHOW COMPLETE SOLUTION AND DRAW ILLUSTRATION
calculate the corresponding depth uniform stress block in a reinforce concrete beam 42*10 deep reinforce with bars 20-mm in a diameter enclosed with 10-mm dia stirrups when the tensile steel strain is 0.008 and concrete compression strain 0.003. f'c = 22 Mpa. Express your anser in 2 decimal places only in mm.
the composite area shown in the figure below is composed of two rectangles. use b = 4.97m., h = 3.73 m. and t =1.48m. determine the radius of gyration about the indicated x-axis.
For the composite area shown in Figure 4.1a, determine the y-coordinate of its centroid. Given B = 450 mm, D = 150 mm, t; = 24 mm, tw1 = 30 mm and tw2 = 45 mm. The positive x and y axes of the coordination system are shown in the figure. B D |-tw1+ - twz