1. The bit period, T, usec. 25 The symbol period, T = usec. Transmission bandwidth, Вт kHz.

Q: O The cathode lead is shorter. It goes to the negative rail

A:

Q: A. B. potentiometer Choose. eddy current sensors Choose. ac excitation ac and dc excitation 1 kHz…

A: Potentiometre which is used to measure the potential difference between the two points this is also…

Q: f you break a magnet in half     it becomes demagnetized     end up with a north pole and a south…

A: Every magnet has two poles north pole and south pole. North pole South pole

Q: If you tested the system with a scan tool and you observed a diagnostic trouble codes DTC P0503 what…

A: The code P0503 means that the engine control mode has received a faulty signal voltage from the…

Q: Vacuum is created in evacuated tube collectors to reduce the heat loss O increase the heat loss…

A: The Evacuated tube authority comprises of various columns of equal straightforward glass tubes…

Q: > Apiece of silver wire has aresistanceof 4.2,0h Lili be the resistanc third the Length and one…

A: We have given the following problem A piece of silver wire has resistance  of 1 ohm what will be the…

Q: draw/make a power supply that will have an output regulated 9Vdc

A:

Q: The error for an ammeter is found as ±2%, the true range of the current it can give for 10 mA is

A: Given: The error for an ammeter, error=±2% Current, I=10 mA

Q: Compare between squirrel cage rotor and drag cup-rotor

A: Given  We need to enumerate the difference between squirrel cage rotor and drag cup rotor  Please…

Q: In STEP 4, you charged the capacitor completely with the PSB set to 3.3V. Then you set the PSB to 5V…

A: Given Initially capacitor charged to 3.3v with PSB set to 3.3v After sometime PSB is set to 5v then…

Q: Questions: 1. What is the threshold voltage, VTH and minimum current that will turn ON the LEDS?

A: As per our policy i have attempted only one question: LED: The full form of LED is a light-emitting…

Q: suggest a method for turning ON the thyrisor which may result in its damge with the diagram

A: Turning ON of a thyristor is nothing but to give external excitation for triggering purposes. There…

Q: 10A ↑ Click here for image R1 Ω * R2 Ω ww • R3 Ω In this circuit R1 = 1/4.00, R2 = 1/2.00 and R3 =…

A: Given data, R1=14Ω, R2=12Ω, R3=19Ω. Given circuit diagram is,

Q: 10 nC -5 nC How much work must you do to move an electron from A to B? The rectangle is 16.6 cm high…

A: Work done to move a electron from A point to B point.  Work done W= q∆V ∆V= VA - VB

Q: 1. Explain the relationship of the measured voltage and the tripping time shown in the graph? What…

A: A graph is given in the question. It shows the values of tripping time corresponding to some values…

Q: For the fixed -bias Configurahion of Figure 1, delermine : a) I BQ b) Ice c) VCEQ O1GV Ice Figure 1…

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: How many 40 W cool white fluorescent lamps would be required to have an initial lamp output of 9,600…

A: Given:Power. P=40WOutput=9600 lumens

Q: draw the point charge and draw the Electric dipoles

A: According to question:

Q: what is the power disipated by R1

A:

Q: Ex (H.W) 32 Calculate the valueof RL Forwhich it will receive marimum the Londi and Calculate the…

A:

Q: Consider a Type K thermocouple used to measure engine exhaust gas temperature in an automotive…

A:

Q: The condition at which a FE

A:

Q: Q9)Determine V2

A: The silicon diode can be turned ON at the voltage of 0.7 V using the KVL find the current from 2.2k…

Q: Dexer mine : To tal Power source

A:

Q: What is the circuit in the given diagram * ?called R D1 D2. VIN Vo VRI T VR2 Not all above Clamper…

A: we will analyze given circuit for different ranges of input voltages. i.e. when diode will conduct…

Q: I have an LED that I want to slowly dim and bring back to full brightness. To which area on my…

A: Generally we use PWM pins in the Arduino board to vary the brightness of the LED by the variation of…

Q: According to the right hand rule, if electrons are flowing into this page, the magnetic field...…

A: according to the right hand rule if electrons are flowing into this page, the magnetic field is: a)…

Q: * What is wrong with this circuit? R₁ 10 kn V₁ 24 V 1N4744A 1 15 V The zener is open. O The zener is…

A: We need to check whether diode is on or off

Q: The arc passes through the body of the insulator is known as O Puncture High current Flashover O…

A: We know that a puncture arc is a breakdown and conduction of the material of the insulator, This…

Q: Zero drift is normally removable by

A: we need to by which we can remove zero drift

Q: On the second part, you did 60-60 because the charge didn't change. Is that correct?

A: Yes you are correct. The current through capacitor is the ratio of  as change in charge to the…

Q: Solve for le of Figure 43. 4.5 mA 0.45 mA Ⓒ3.56 MA Ⓒ 0.356 mA V VCC T21V R1 $500KQ R2 $2.1kQ Q1 Beta…

A:

Q: Answer the questions and submit the photos for questions 2 - 9using the circuit from STEP 2. R1 50 Q…

A:

Q: Ob Oc n the following circuit junctions diagrammed below, which combination of current directions is…

A:

Q: finding the voltage to each resistance?

A:

Q: A -600 µC charge (blue charge) and a 800 µC charge (red charge) are positioned as shown in the…

A:

Q: Attempt Only if you are sure . a 24 V DC voltage source is controlled by a rotational potentiometer.…

A: Given data At θ=0°C, V0°C=24 V At θ=12°C, V12°C=10 V To find out We have to determine the voltage…

Q: electric machine

A:

Q: What is the difference between a TON and RTO timer?     none     TON is on delay and RTO is off…

A: What is the difference between a TON and RTO timer To select from the given options

Q: tined The vame of R in Fig belouf the woltage drop across the 5s2 is 2-5 volts? I A Ia I, R 12 v D

A:

Q: (2) j Which one of the following distributions that required the maximum work to assemble the…

A:

Q: Ability Of Source To Produce Light In Each Direction is measured in terms of- a. CANDELA b. FOOT…

A: The ability of souce to produce the light in given direction is called as luminious intensity.