1. List some of application that you can controlled by a potentiometer. 2. Explain the function of map instruction in the code program that you have written in procedure. 3. Controlling the time blinking rate of two LEDs by using potentiometer Assumptions: 1  Potentiometer connected to A2 2  LED 1 connected to PIN 6 3  LED 2 connected to PIN 9 4  When the potentiometer is changed, blinking rate of the two LED is changed from 2 to 4 seconds.

Q: The function of the segment register in protected mode operation is discussed.

A:

Q: As figure shows, please filling the blank to finish the program to turn on the LEDS as following:…

A: Answer: Our instruction is answer the first three part from the first part and . I have given…

Q: What kind of operands may be used with the FADD instruction?

A: operands that may be used with the FADD instruction are listed below.

Q: The designer needs for...... state boxes for drawing the ASM-chart for

A: ANSWER IS IN THE BELOW STEP

Q: The ON state of bool type variable can be expressed by: O Only normally open contact instruction.…

A: Here we have given correct option for the asked question. You can find the solution in step 2.

Q: 5. All the interrupts are enabled using a special function register called

A: All the interrupts are enabled using a special function register called interrupt enable register…

Q: Write a C code for bare metal that will perform the following functions on STM32F103rb. a)    Switch…

A: Let us assume that S1 = PIN1.0 , S2 = PIN1.1 , LED1 = PIN1.2 , LED2 = PIN1.3

Q: Compare CALL and PUSH instructions

A:

Q: Write python code for a "Count down clock and timer" Explain how the c

A: Required: Write python code for a "Count down clock and timer" Explain how the code works

Q: should stay off for 3 seconds and then the LED should blink 10 times at a rate of 1 Hz (on and off

A: byte i; void setup()  {   pinMode(3,OUTPUT); } void loop() {   digitalWrite(3,HIGH);…

Q: 1.) You have two servo motors connected to PC0 & PC1, two switches connected to PBO and PB1 and one…

A: ANSWER :

Q: Determine the value in R17 for the following AVR instructions:

A: Registers, a memory location with the actual processor that work at very fast speeds. It stores…

Q: There are several reasons why shift registers need edge triggers.

A: Dear learner, hope you are doing well, I will try my best to answer this question. Thank You!!

Q: Edge triggers should be utilized in shift registers for a variety of reasons.

A: Introduction: A shift register is a form of a digital circuit that employs a cascade of flip-flops,…

Q: mov al, -128     neg al why is the carry flag, sigh flag and overflow flag set to 1 when we peform…

A: This particular question belongs to Computer Science and Engineering. Computer Science is an…

Q: Read 2 numbers a and b from serial monitor and write function that will compare them and return -1…

A: Given, Read 2 number a and b compare ab print result

Q: List various flags in the status Register.

A: Flags in the status register represents various special conditions linked with each flag.

Q: FIGURE 8.95 Problem 8.1: Timing Diagram

A: SR latch output is HIGH, when the SET (S) is active high. SR latch output is LOW, when the RESET (R)…

Q: (b) Describe the state diagram below in detail. Hint: This state machine describes the operation of…

A: The educational objective of this laboratory is to investigate the creation of custom IP to…

Q: Select the logical shift instruction that multiplies the contents of EAX by 8. sal eax, 8 sar eax, 8…

A: SHL instruction stands for Shift Left.

Q: Need of vhdl code to answer and you have time Add an asynchronous RESET, active High to the state…

A: A VHSIC Hardware Description Language (VHDL) is a hardware description language (HDL) that can…

Q: What is a major reason for "signal multiplexing" or "pin multiplexing" in a microcontroller? Allow…

A: Given

Q: write a code that controls a stepper Motor from a parallel port using a pc

A: solution in below step:-->                    stepper Motor from a parallel port using a…

Q: Work #6: MISO DIGITAL SYSTEMS (The NAND Gate) Write the routine a microcontroller-based security…

A: Answer: I have given answered in the handwritten format in brief.

Q: int i; for (i=0;i=2){ GPIOD_ODR &=~(1<<(i-2)); } } At each iteration what is LEDS that will be on…

A: According to the question, we have to explain that at each iteration which LED will be ON. In Step 2…

Q: Write a logical shift instruction that divides EAX's contents by 16

A: A logical shift instruction that divides EAX's contents by 16:

Q: Question 3 The instruction push eax Group of answer choices copy the content of the element pointed…

A: Assembly language is often used in systems programming, device driver development, and other tasks…

Q: diagra escribes operation of a servo motor (scans three angles 0°, ± 90º) based on the pushbutton…

A: what is servo motor? The servo motor is used for servo system. The servo system is a control system…

Q: In Assembly What is the value of the carry flag if you store a 6 into the AX register, and compare…

A: The answer is

Q: Edge triggers should be utilized in shift registers for a variety of reasons.

A: Introduction: Shift registers are used to store temporary data. Additionally, shift registers are…

Q: A circuit has a pushbutton switch connected to pin PD0 and a servomotor connected to PC0 of AVR…

A: #define F_CPU 1000000UL #include&lt;avr/io.h&gt; #include&lt;util/delay.h&gt; void main() {…

Q: PUSH and POP instruction always transfer one byte of data : TRUE or FALSE?

A: answer is

Q: write a C program that utilizes the RTC alarm to toggle an LED every five seconds

A: a) #include &lt;stdio.h&gt; #include &lt;time.h&gt; int main(void) { time_t now; struct…

Q: Q1/Give the operation (function) for every section: 1.ALU 2.EFI in (8284A) IC 3.RISC 4. program…

A: ANSWER: 1. ALU

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.