Choose the correct answer of the following questions:1. If no external impressed force acts on the system, the total momentum (G) of a system ...c. remains constanta. increasesb. decreasesd. none of the these2. Which of the following cases momentum is conserved?(1 M)a. Perfectly elastic impactd. Momentum is always conservedc. Perfectly inelastic impactb. plastic impact with 0

Dear student, According to the guidelines I am allowed to answer only one…

Answered: 1. If no external impressed force acts…

1. If no external impressed force acts on the system, the total momentum (G) of a system ........... a. increases b. decreases c. remains constant d. none of the these

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A jet plane discharges a jet at the rate of 30 kg/s with a velocity of 1,000 m/s relative to the plane. If the forward speed of the plane is 900 km/h, find: (a) The thrust on the plane. Q6 (b) The power developed at the jet.
A jet strikes a stationery curved vane without shock and is deflected 150° from its original direction. The discharge from the jet is 0.68kg/s and the velocity is 24m/s. Assume that there is no reduction of relative velocity due to friction and determine the magnitude and direction of the
A mass-spring system is initially compressed towards a wall and hold in equilibrium withthe help of a forceF. At timet=0sec, the force Fis suddenly released. The mass-spring system then reaches a velocityvwhile sliding on the frictionless surface. (a) Is the linear momentum conserved? (b) Calculate the average force exerted by the wall on the mass-spring system after theforceFis released, assuming that the spring remains in contact with the wall for a shorttimeΔt. Express your answerin terms of k,m,Δt and F.
A stream of water flowing at a rate of 1.2 m3/min and moving with a speed of 30 m/s at both A and B is deflected by a vane welded to a hinged plate. Knowing that the combined mass of the vane and plate is 20 kg with the mass center at point G , determine (a) the angle 0, (b) the reaction at C.
2. Consider a two-stage rocket designed to provide an ideal AV of 3000 m/s. The following information is known: The following information is known: Payload mass = 100 kg 1st Stg: y = 0.9, Isp 250 sec, 45% of Total AV 2nd Stg: y = 0.85, Isp 300 sec, 55% of Total AV While the y values quoted above account for the propulsion systems, the interstage structure is generally treated separately. Assume that the weight of this component is equivalent to 5% of the mass of the Stg2/payload combination it supports. Determine: a) Stage 2 propellant and inert masses b) Interstage mass c) Total vehicle mass
During terrible weather at a ski-flying world championship, a ski jumper tried to adjust for bad conditions midway down the ramp but completely lost control and tumbled wildly off the side at its bottom into a scattering crowd. The 73-kg jumper left the ramp about 45 m lower than his starting position. If the ski jumper had simply fallen straight down 45-m rather than skiing down a ramp, would his kinetic energy increase?
A Boeing 747 airliner which weighs 802,000 lb taxis down a runway and reaches a velocity of 75.0 mi/h. The airplane starts from rest, and its engines can deliver 175,000 lb of thrust. (a) Find the plane's mass. (b) Find its momentum. (c) Find its change in momentum. (d) In order to reach this velocity, what impulse was delivered to the plane? (e) How long did the plane take to reach its speed? (Assume that the thrust of the engines remains constant and ignore air resistance.)
1. (a) Consider two vectors with 7 = 8m î and a linear momentum acting on a particle is given byp = 3Nî – 3Nj. Determine the magnitude and direction of angular momentum acting on the particle. (b) Fig. 1 shows the variation of linear momentum as a function of time. Rank different segments of Fig. 1, according to the magnitude of force, in descending order. (c) Specify the condition of conserving linear momentum of a system of Figure 1 particles.
Small steel balls, each with a mass of 150 g, enter the semicircular trough (Radius =0.92 m) in the vertical plane with a horizontal velocity of VA=7.9 m/s at A. Friction is negligible. UB B VA A velocity at C (m/s) a. 6.66 о Б.7.99 c. 5.33 d. 9.33 e. 2.66 normal reaction at C velocity at B (m/s) О а. 6.16 b. 5.13 C. 4.11 d. 3.08 е. 2.05 O O
A jet issued of water at the rate of 200 L/s and a velocity of 36 m/s strikes a blade moving in the same direction at 15 m/s. The deflection angle of the blade is 120°. Neglecting friction, determine: (a) the x- and y-components of the force exerted by the jet on the blade in N.; (b) the work done by the jet on the blade, in joules.
Consider an airplane with a jet engine attached to the tail section that expels combustion gases at a rate of 18 kg/s with a velocity of V = 300 m/s relative to the plane. During landing, a thrust reverser (which serves as a brake for the aircraft and facilitates landing on a short runway) is lowered in the path of the exhaust jet, which deflects the exhaust from rearward to 120°. Determine (a) the thrust (forward force) that the engine produces prior to the insertion of the thrust reverser and (b) the braking force produced after the thrust reverser is deployed.
A water jet strikes a triangular block resting on a stationary table and is deflected 30° as shown in Fig. B.5. The mass flow rate of the water jet is gradually increased to 30 kg/s such that the block starts to slide on the table. The mass of the block is 1.5 kg. Assuming that the weight of the water can be neglected, and the inlet and outlet velocities of the jet are the same and remain unchanged. Outlet Inlet Water jet Triangular block 30 Fig. B.5 (a) Determine the horizontal and vertical forces against the block due to the water jet, in terms of the velocity of the water jet, V. (b) If the cross-sectional area of the water jet is 40 cm?, determine the velocity of the water jet and the coefficient of friction, µ between the block and the table.