B8 A stream of water flowing at a rate of 1.2 m³/min andmoving with a velocity of magnitude 30 m/s at both A and Bis deflected by a vane welded to a hinged plate as shown inthe figure.110 mmC300 mm30 mmKnowing that the combined mass of the vane and plate is 36 kg with themass center at point G, determine and the reaction at C.The reaction at C is 383.07 N 87.2

To find : The reaction at point C. Given : The water flowing rate is m˙=1.2 m3min 1000 mm1 m1…

A stream of water flowing at a rate of 1.2 m³/min and moving with a velocity of magnitude 30 m/s at both A and B is deflected by a vane welded to a hinged plate as shown in the figure. 110 mm 300 mm 41 30 mm nowing that the combined mass of the vane and plate is 36 kg with the ass center at point G, determine and the reaction at C. he reaction at C is 383.07 N 87.2

A stream of water flowing at a rate of 1.2 m³/min and moving with a velocity of magnitude 30 m/s at both A and B is deflected by a vane welded to a hinged plate as shown in the figure. 110 mm 300 mm 41 30 mm nowing that the combined mass of the vane and plate is 36 kg with the ass center at point G, determine and the reaction at C. he reaction at C is 383.07 N 87.2

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

When it hails, each golf ball-sized chunk of hail rained down with a mass of 0.025 kg mass and impacted my car with a velocity of 400 m/s. The hood of the car is made out of 1040 steel. The modulus of elasticity is 207 GPa, the YS is 490 MPa, and the UST is 590 MPa. A. Determine the amount of energy (or work) that the steel hood of my car could absorb before being Plasticly deformed. Assume that the cross-sectional area impacted by the hail is 0.0005 m2 and that the thickness of the steel is 0.005 m. B. Determine the amount of energy (or work) that the steel hood of my car could absorb before being fractured. Assume that the cross-sectional area impacted by the hail is 0.0005 m2 and that the thickness of the steel is 0.005 m.
A shaft 180 mm diameter is supported in two bearings 2.5 metres apart. It carries three discs ofmass 250 kg, 500 kg and 200 kg at 0.6 m, 1.5 m and 2 m from the left hand. Assuming the mass ofthe shaft 190 kg/m, determine the critical speed of the shaft. Young’s modulus for the material ofthe shaft is 211 GN/m2.
6-23 A reducing elbow in a horizontal pipe is used to deflect water flow by an angle 0 = 45° from the flow direction while accelerating it. The elbow discharges water into the atmo- sphere. The cross-sectional area of the elbow is 150 cm² at the inlet and 25 cm² at the exit. The elevation difference between the centers of the exit and the inlet is 40 cm. The mass of the elbow and the water in it is 50 kg. Determine the anchoring force needed to hold the elbow in place. Take the momentum- flux correction factor to be 1.03 at both the inlet and outlet. 150 cm² Water 30.0 kg/s FIGURE P6-23 25 cm² 15- 40 cm
3600s Table 1-2, 1 ft = 0.304 8m. Thus, 0.556m 1 ft 0.556m/s = 0.3048m =1.82 ft / s Note: Remember to round off the final answer to three significant mple 2: Convert the quantities 300 lb.s and 52 slug/ft° to appropriate S ation: Using Table 1-2, 1 lb =4.448 2 N 4.448N 300 lb.s = 300 lb.s * 1 lb 1334.5N.s 1.33KN.s %3D 14.593 8 kg and 1 ft = 0.304 8 m, then
To get up on the roof, a person (mass 85.0 kg) places a 6.20 m aluminum ladder (mass 15.0 kg) against the house on a concrete pad with the base of the ladder 2.00 m from the house. The top of the ladder rests against a plastic rain gutter, which we can assume to be frictionless. The center of mass of the ladder is 2.00 m from the base, as measured along the ladder. The person is standing on the ladder 3.00 m from the base, as measured along the ladder. Find the normal reaction and friction forces (in N) on the ladder at its base. (Enter the magnitudes.)
A 1 kg collar can slide on a horizontal rod, which is free to rotate about a vertical shaft. The collar is initially held at A by a cord attached to the shaft. A spring of constant 30 N/m is 450 mm -150 mm attached to the collar and to the shaft and is undeformed when the collar is at A. As the rod rotates at the rate 0=16 (A В rad/s, the cord is cut and the collar moves out along the rod. Neglecting friction and the mass of the rod, determine (a) the radial and transverse components of the acceleration of the collar at A, (b) the acceleration of the collar relative to the rod at A, (c) the transverse component of the velocity of the collar at B.
A 40 kg-mass hangs from the end of a uniform beam. The beam is 6.0 m long and has a mass of 60 kg. The beam is supported at the left end by a hinge at the wall and by a cable at the right end. The other end of the cable is tied to the wall at a point 4.0 m above the left end of the beam. (g = 9.81 m/s² )A. Draw the FBD;B. Find the tension (T) in the supporting cable in Newtons; andC. Find the reaction force (R) of the hinge on the beam ( magnitude and direction).
(c) A 2.00 kg block hangs from the end of a 1.50 kg, 1.00 m long rod, togat her forming a pendulum that swings from a fridionless pivot a the top end of the rod. A 10.00 g bullet is red horizontal into the block, where it sticks, causing the pendulum to swing out to a 30:00 angle as shown in Figure 5. Calaulate the initial speed of the bullet and leave your answer in terms of ! 1. Use Irod = ML?, where M and L are mass and length of %3D the rod, respectively. e= 30° d- 1.0 m m - 1.5 kg dcose m, - 0.010 kg TAy -da w, - O rad/s = 0 m/s m, = 2.0 kg Ve - 0 m/s Figure 5: The bullet hitting pendulum
A baseball (radius = .0366 m, mass = .145 kg) is dropped from rest at the top of the Empire State Building (height = 1250 ft). Calculate (a) the initial potential energy of the baseball, (b) its final kinetic energy, and (c) the total energy dissipated by the falling baseball by com- puting the line integral of the force of air resistance along the baseball's total distance of fall. Compare this last result to the difference between the baseball's initial potential energy and its final kinetic energy. (Hint: In part (c) make approximations when evaluating the hyperbolic functions obtained in carrying out the line integral.) 2.9
1. A reversing elbow used to deflect water flow at a rate of 14 kg/s in a horizontal pipe to make a U-turn before it is discharged into the atmosphere, as shown in Figure 1. The cross-section area of the elbow is 113 cm² at the inlet and 7 cm² at the outlet. The elevation difference between the centers of the outlet and inlet is 30 cm. Neglecting the weight of the elbow and the water in it and assuming the flow is frictionless, determine the anchoring force needed to hold the elbow in place. mv₂ mV₁ O Figure 1.
Oc 587.10015 d.505.20015 669.00015 Arigid rectangular tank of a volume of V-15.3 m contains Nitrogen. At t=0.0, Nitrogen enters the tank with a speed of 50 m/s and a density of 7 kg/m and escapes the tank with speed V=120 m/s and density of 6 kg/m. Find the rate of change of Nitrogen density in the tank at t=0.0. 3 A=0.2 m Nitrogen A=0.2 m Rigid tank
During the packaging process, a can of soda of mass m = 0.4 kg moves down a surface inclined 20° relative to the horizontal, as shown in the figure below. The difference between the initial height of the can and the final height of the can is dz = 2 m. The can is acted upor by a constant force R parallel to the incline and by the force of gravity. The magnitude of the constant force R is 0.05 N. Ignoring friction between the can and the inclined surface, determine the can's change in kinetic energy, in J, and whether it is increasing or decreasing. Let g= 9.8 m/s². Initial location m R = 0.05 N Final location dz 20°