1. From a clear water reservoir 3 m deep and maximum water level F at 30.00, water is to be pumped to an elevated reservoir at 75.00 at the constant rate of 9,00,000 litres per hour. The distance is 1500 m. Give the economical diameter of the rising main and the water horse power of the pump. Neglect minor losses and take f = 0.01. %3D

1. From a clear water reservoir 3 m deep and maximum water level F at 30.00, water is to be pumped to an elevated reservoir at 75.00 at the constant rate of 9,00,000 litres per hour. The distance is 1500 m. Give the economical diameter of the rising main and the water horse power of the pump. Neglect minor losses and take f = 0.01. %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Hydrodynamics pumps (WRITTEN COMPLETE SOLUTION AND FIGURES IF NEEDED) 1. A centrifugal pump installation draws water from an open reservoir having a water elevation of 5 m above the pump centerline and delivers the water to another open reservoir 80 m above pump centerline. The rate of discharge is 600 li/min. The suction pipe has a diameter of 200 mm while that of the discharge pipe diameter is 150 mm. The friction loss at the suction is estimated to be 4 times the velocity head at the 200 mm suction pipe. At the discharge, the friction loss is estimated to be 21 times the velocity head at the 150 mm discharge pipe. If the overall mechanical efficiency is 77%, estimate the brake power input to thepump. a. brake power Answer : ____________________ kW
14. Water is pumped from one tank to another through a 0.100 m smooth plastic tube. The flow rate is 0.200 m³/s. The head loss due to major and minor friction losses is given by the equation, h₁ = 12.0 2g V 25 m Pump Determine the pump head. Also determine the shaft work done by the pump.
A cylindrical tank of water is 20 m in diameter and 3.5 m tall. There is a 1.0 cm diameter hole at the bottom from which water is leaking. A feeder pipe at the top of the tank, 4.0 m above the ground delivers water at a rate of 0.02 m/min. Ir the tank is initially half full, tal what is the water flow rate in m^3/sec from the top feeder pipe? (bi what is the pressure at the bottom of the tank? (Hint: Bernoul's principle) () what is the water speed at the bottom? (d) what is the leaking flow rate at the bottom? fe) at what rate is the volume of water changing? (Assume the tank is open to air at the top)
Reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which meets at the junction D. Reservoir A is at elevation 80 m, reservoir B is at elevation 50 m, and reservoir C is at elevation 10 m. Diameter Length Friction Factor 400 mm 500 mm Pipe 1800 m 2000 m 1 0.02 2 0.025 3 800 mm 4000 m 0.03 a. Compute the discharge flowing out of reservoir A. b. Determine the discharge flowing in or out at reservoir B. c. Find the discharge flowing towards reservoir C.
Water is pumped from a supply reservoir to a ductile iron water transmission line. The high point of the transmission line is at point A 1 km downstream of the supply reservoir and the low point of the transmission is at point B 1 km downstream of point A. If the flow rate through the pipeline is 1m³/s the diameter of the pipe is 750mm and the pressure at A is to be 350 kPa. A) estimate the head that must be added by the pump. B) estimate the power supplied by the pump. C) calculate the water pressure at B.
4. Two reservoir A and B, feed a third reservoir C as shown in figure. Assuming constant water level in the figure and making use of the data given in the table below. Compute the discharge in each pipe. Use conventional solution. EL 205 m EL 130 m 2 EL 192 m Q₁ = 0.3963 m³/s, Q₂ = 0.4550 m³/s, Q3 = 0.8513 m³/s Pipe 1 2 3 n 0.011 0.014 0.017 Diameter Length (mm) in (m) 400 500 800 1800 2000 4000
A 1 2 The three-reservoir system is shown below: 3 C The elevation of Reservoir at A is 140m and at Cis 50m. The flow rate at Pipe 1 from Reservoir A is 1.75 m/s. All pipes have a length of 500 meters, friction factor f - 0.02, and sizes namely: Pipe Diameter 1 (mm) = 600mm Pipe Diameter 2 (mm) = 500mm Pipe Diameter 3 (mm) - 400mm Determine the elevation of Reservoir B in meters.
An engineer is hired to design a swimming pool 15 m long by 6 m wide by 2 m deep. For water supply, he decides to lay 600 m of 5 cm pipe with f = 0.020 from a nearby main to the pool. The pipe will discharge freely into the pool during the entire filling process. The average pressure at the water main is 550 kPa and the difference in elevation between the two ends of the pipe is 10 m, with the discharge end higher than the intake end. Assuming that 10 % of the loss in the pipeline are due to transitions, fittings, and valves, how long will it take to fill the swimming pool?
SITUATION 4: Water is drained from a large reservoir using two horizontal pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4- cm diameter. The water level in the reservoir is 18 m above the center line of the pipe. The pipe entrance is a sharp edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. Assume the friction factor for all pipes is equal to 0.02 and the loss coefficient is 0.05 for a sharp edged entrance, and is 0.46 for sudden contraction. 18 m Oil tank 20 m 35 m
2. Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Pipe 1: L = 5000 m, D = 300 mm Pipe 2: L = 4000 m, D = 250 mm Pipe 3: L = 3500 m %3D The flow from reservoir A to junction P is 0.045 m3/s and f for all pipes is 0.018. (a) Find the elevation of the energy grade line at P in m (b) Determine the flow on pipe 2 in m3/s (c) Compute the diameter appropriate for pipe 3 in mm
Three reservoirs A, B, and C are connected by pipeline 1, 2 and 3 respectively which merges at a junction X. The elevation of reservoir A is 350 m and that of B is 290m. The rate of flow from A is 1.5 m^3/s. (See the table) 1. Compute the rate of flow in reservoirs B and C. Pipes Diameter Length Friction factor “f” 1 825 mm 1500 m 0.0155 2 650 mm 450 m 0.0165 3 450 mm 1200 m 0.0175
2] A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.