Problem-4, A pipe of 0.7 m diameter has a length of 6 km and connects two reservoirs A and B. The water level in reservoir A is at an elevation 30 m above the water level in reservoir B. Halfway along the pipe line, there is a branch through which water can be supplied to a third reservoir C. The friction factor of the pipe is 0.024. The quantity of water discharged into reservoir C is 0.15 m³/s. Considering the acceleration due to gravity as 9.81 m/s² and neglecting minor losses, the discharge (in m³/s) into the reservoir B is

Problem-4, A pipe of 0.7 m diameter has a length of 6 km and connects two reservoirs A and B. The water level in reservoir A is at an elevation 30 m above the water level in reservoir B. Halfway along the pipe line, there is a branch through which water can be supplied to a third reservoir C. The friction factor of the pipe is 0.024. The quantity of water discharged into reservoir C is 0.15 m³/s. Considering the acceleration due to gravity as 9.81 m/s² and neglecting minor losses, the discharge (in m³/s) into the reservoir B is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 170-m long pipeline, composed of two pipes connected in series, discharges freely at a point 40 m below the water level at intake. The pipe projects into the reservoir. The first 100 m is 25 cm in diameter, and the remaining 70 m is 15 cm in diameter. Assuming that f=0.05 for both pipes, (a) find the rate of flow. If the junction of the two sizes of pipe is 25 m below the intake water-surface level, find the pressure head just above C and just below C, where C denotes the point of junction. Assume a sudden contraction at C. Use k=0.8 for entrance, 0.24 for sudden contraction and 1.0 for exit. I will downvote the incorrect solution
Two sharp-ended pipes of diameter d₁ = 50 mm, and d₂ = 100 mm, each of length 100 m, are connected in parallel between two reservoirs which have a difference of level h= 10 m, as shown in figure below. If the friction coefficient, f= 0.032 for each pipe, calculate: a. the rate of flow for each pipe, b. the diameter d of a single pipe 100 m long which would give the same flow if it was substituted for the original two pipes, (Notes: Use Darcy Weisbach's equation, h,= (flv²)/(2dg) Pipe 2- Pipe 1 h = 10 m 110
Water is being pumped at a steady rate of 500 gpm from a 12in diameter well. Thewell draws water from an unconfined aquifer. The height of water in the aquifer in the equilibrium statebefore pumping is 100ft, and the drawdown at the well at steady state pumping is 40ft. The hydraulicconductivity of the aquifer determined from a pump test is 0.02ft/min. Determine the radius of influence.
5 (c)
Two reservoirs, A and B, are 7.5 km away from each other and connected by a 900 mm steel pipe ( f = 0.02). If reservoir A is 10 m higher than reservoir B, the pressure at B is 90 kPa greater that the pressure at reservoir A, what is the amount and direction of flow of water in the pipe. Use f = 0.02.
please consider minor and major losses
An engineer is hired to design a swimming pool 15 m long by 6 m wide by 2 m deep. For water supply, he decides to lay 600 m of 5 cm pipe with f = 0.020 from a nearby main to the pool. The pipe will discharge freely into the pool during the entire filling process. The average pressure at the water main is 550 kPa and the difference in elevation between the two ends of the pipe is 10 m, with the discharge end higher than the intake end. Assuming that 10 % of the loss in the pipeline are due to transitions, fittings, and valves, how long will it take to fill the swimming pool?
SITUATION 4: Water is drained from a large reservoir using two horizontal pipes connected in series. The first pipe is 20 m long and has a 10-cm diameter, while the second pipe is 35 m long and has a 4- cm diameter. The water level in the reservoir is 18 m above the center line of the pipe. The pipe entrance is a sharp edged, and the contraction between the two pipes is sudden. Neglecting the effect of the kinetic energy correction factor, determine the discharge rate of water from the reservoir. Assume the friction factor for all pipes is equal to 0.02 and the loss coefficient is 0.05 for a sharp edged entrance, and is 0.46 for sudden contraction. 18 m Oil tank 20 m 35 m
2] A pipe discharges 130 lps of water into a reservoir at a point 1.85 m belowthe water surface. At point A the diameter is 25.4 cm and the center of the pipe is 1.25m above the water surface. At the discharge end the pipe is 30.5 cm. If the head lossfrom A to the reservoir is 0.7 m, determine the pressure in A.
M - Problem 3: For these three reservoirs please assume that the elevations of the waterlines in reservoirs 1-3 are: h, 30 m, h₂-20 m, and h, 10 m. Also, please assume that the lengths of pipes 1-3 are L₁ 1000 m, L₂ 2000 m, and L3 = 3000 m; the diameters of all three pipes are D₁ D₂ D₂ = 2.0 m; and the friction coefficients of all three pipes are f f₂=fa=0.015. If you estimate that the total head at Junction "J" is H, = 22 m please: 1) calculate the resulting net volumetric flow rate into junction "J" and 2) determine if the actual total head at junction "J" is above or below H, = 22 m. h₂ Reservoir 1 h₂ 7 Reservoir 2 Pipe D Reservoir 3 ha Pipe 3 Pipe 2 a
Q.solve itt.