1. For the shown conic body which rotating with constant angularvelocity 10 rad/s, find the torque which effected by viscosity of the ol thatsurrounding the conic body.Take:Radius of the cone is 2 in Height of the cone is 4 inOil viscosity is 3.125x107 Ib.s/in?Answer : Torque =0.02535 Ib. InP10 rad/k0.01-in film0.01 in

Dear student, The required things given to us are as under Angular velocity Radius of base of cone…

1. For the shown conic body which rotating with constant angular velocity 10 rad/s, find the torque which effected by viscosity of the oil that surrounding the conic body. Take: Radius of the cone is 2 in Height of the cone is 4 in Oil viscosity is 3.125x107 Ib.s/in? Answer : Torque =0.02535 Ib. In P10 rad/s 0.01-in film

1. For the shown conic body which rotating with constant angular velocity 10 rad/s, find the torque which effected by viscosity of the oil that surrounding the conic body. Take: Radius of the cone is 2 in Height of the cone is 4 in Oil viscosity is 3.125x107 Ib.s/in? Answer : Torque =0.02535 Ib. In P10 rad/s 0.01-in film

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A piston rod is subjected to a maximum compression load of 32000 lbs. and is 20 in.long. The material for the rod has a yield strength of 73 ksi. The Rankine’s constant canbe taken as 0.00026. What would be the diameter of the rod for a factor of safety of 4?a. 1.61 inb.0.97 inc. 1 ind.1 3/4 in.
2. Determine the magnitude of F so that the particle is in equilibrium. Take A as 12 kN, B as 5 kN and C as 9 kN. A kN 30 60° C kN B kN
A brass disk of radius 0.7 ftft and weight 459 lblb sits in a right-angle groove made of granite. The disk makes contact with the groove at AA and BB and the coefficient of static friction at both points are μS=μS= 0.39 A couple moment of MM is applied to the disk as shown.
A 25-mm-diameter shaft is pulled through a cylindrical bearing as shown in Figure. The lubricant that fills the 0.3-mm gap between the shaft and bearing is an oil having a kinematic viscosity of 8x10 m²/s and a specific gravity of 0.91. Determine the force P required to pull the shaft at a velocity of 3 m/s. Assume the velocity distribution in the gap is linear. Bearing Shaft 0.5 m Lubricant
Steel bars and an aluminum bar support the rigid slab as a platform as shown below. A gap A= 0.26 mm exists between the aluminum bar and the slab. Neglecting the weight of the slab a (/degree celsius) 11.6х106 23.1x106 A (mm²) Steel bar Aluminum bar E (GPa) 200 70 350 400 a) Which temperature increase AT is required to just close the spacing at the middle? (Note that the temperature increase will subject all bars) b) What are the stresses in the steel bars and aluminum bar for AT = 90 degree celsius in MPa? 1000 mm Steel Aluminum Steel
Problem Determine the value of Ely midway between the supports for the beam loaded as shown in Fig.. El y = 0950 N-m³ answer M = 1800 Nm 2m R₂ 2 m 200 N/m 2 m R₂ 2 m
A 100- m steel tape is used to measure the distance of the line and found to be 1539.28 m long. During measurement, the tape is supported the ends under a pull of 10 kg and the observed mean temperature is 31 deg. Celsius. The tape is of standard temperature of 20 deg. Celsius and a tension of 12 kg. The cross-sectional area of the tape is 0.035 sq. cm. The coefficient of linear expansion is 0.0000116/ deg. Celsius and the modulus of elasticity of steel is 2.0 x 106 kg/ sq. cm. The tape weighs 1.5kg. a) Determine the total correction for temperature. b) Determine the total correction due to sag. c) What is the correct length of the line? From the answer that you obtain from the above question, write a brief conclusion. Is it liable and okay to obtain this amount of error? Explain.
The beam has a Young's modulus of Eo 100 GPa, a length of / = 4 m and 2nd moment of area of I₂ = 4 m². The intensity of the uniformly distributed load is w = 100 N/m. Now calculate the maximum beam deflection: Umax = X Expected answer: 0.1149623254 (m)
The 113-lb force P is applied to the 230-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μs = P Answer: F = 0.48, Mk = 0.38. i Mk lb
A 100- m steel tape is used to measure the distance of the line and found to be 1539.28 m long. During measurement, the tape is supported the ends under a pull of 10 kg and the observed mean temperature is 31 deg. celsius. The tape is of standard temperature of 20 deg. celsius and a tension of 12 kg. The cross sectional area of the tape is 0.035 sq.cm. The coefficient of linear expansion is 0.0000116/ deg. celsius and the modulus of elasticity of steel is 2.0 x 10^6 kg/ sq. cm. The tape weighs 1.5kg.a) Determine the total correction for temperature.b) Determine the total correction due to sag.c) What is the correct length of the line?d.) Write a brief conclusion on the answer that you obtain from the above question. Is it liable and okay to obtain this amount of error?