Discussion: 1. Does plane section (square plane) on the surface of the circular shaft remain plane after loading for the shaft under torsion (compare between elastic and plastic deformation)? Justify your answer by drawing vertical and horizontal lines over the shaft length. 2. How is shear modulus related to Young's modulus? 3. Does the distance from the cross section neutral-axis effects the calculated shear stress? How? 4. Solid and hollow aluminum shaft with same outer diameter, which will twist more? Why?

Discussion: 1. Does plane section (square plane) on the surface of the circular shaft remain plane after loading for the shaft under torsion (compare between elastic and plastic deformation)? Justify your answer by drawing vertical and horizontal lines over the shaft length. 2. How is shear modulus related to Young's modulus? 3. Does the distance from the cross section neutral-axis effects the calculated shear stress? How? 4. Solid and hollow aluminum shaft with same outer diameter, which will twist more? Why?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 42 meter solid shaft is under torsional loading 53 Nm. If in this application, the allowable shear stress for the material is 369 MPa. Calculate the required minimum diameter of the shaft: _____ mm ( input the value directly from your calculation before rounding it up to an engineering accepted diameter) Pay attention to units, and calculate your answer to one decimal place.
The composite bar is subjected to a normal force P = 7500 lb as shown in the figure. The section of the composite bar is composed of two hollow tubes and a solid steel core. Determine the axial stress developed in each bar. Use Ecu = 18 x 106 psi, Est = 30 x 106 psi, and Ebr = 16 x 106 psi.
A small aluminum alloy [E = 65 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 125 mm. The cross-sectional dimensions of the tee shape are b = 15 mm, d = 23 mm, and t = 9 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 460 με is measured from a strain gage located at c = 9 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P?
Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm. The cross-sectional dimensions of the beam areb1 = 35 mm, d1= 115 mm, b2= 21 mm, d2 = 21 mm, and a =7 mm. For this material, the allowable tensile bending stress is 15 MPa, and the allowable compressive bending stress is 14 MPa. Determine the largest moment M that can be %3D %3D %3D %3D %3D %3D applied as shown to the beam. b2 a 不 d2 d1 b1 Answer: N-m M% =
The steel pipe shown has an outside diameter of 175 mm, a wall thickness of 18 mm, an elastic modulus of E = 200 GPa, and a coefficient of thermal expansion of ? = 11.7 x 10-6/°C. Using a = 335 mm, b = 870 mm, and ?= 60°, calculate the normal strains at Hand K after a load of P= 45 kN has been applied and the temperature of the pipe has been increased by 35°C O 16 mm, an e load of P= 45 kN has been applied and the temperature of the pipe has been increased by Answers: EH = Ek= H K με με
A small aluminum alloy [E = 80 GPa] tee shape is used as a simply supported beam as shown. For this beam, a = 165 mm. The cross- sectional dimensions of the tee shape are b = 19 mm, d = 29 mm, and t = 7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 430 µɛ is measured from a strain gage located at c = 10 mm below the topmost edge of the tee stem at section 1-1. What is the applied load P? P ЗР Strain gage d D E H Answer: P = i
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
A thin polymer plate PQR is deformed so that corner Q is displaced downward 0.9 mm to new position Q', as shown in. Determine the shear strain at Q' associated with the two edges (PQ and QR). Assume a = 150 mm, b = 216 mm, c = 180 mm, and A = 0.9 mm. a b P R C Answer: Shear strain y = Q i A X urad.
The solid circular drill rod AB is made of a steel that is assumed to be elastoplastic with τY = 22 ksi and G = 11.2 × 106 psi. Knowing that a torque T = 72 kip·in. is applied to the rod and then removed, determine the maximum residual shearing stress in the rod. The maximum residual shearing stress in the rod is ksi.
A load P is applied to a steel component which is supported an aluminum plate into which a 12 mm diameter hole has been drilled. Knowing that the maximum allowable shearing stress is 86.5 MPa in the steel and 160 MPa in the aluminum plate, determine the largest load which may be applied to the steel component. Provide your answer in kN with precision to two decimal points. 10 mm Answer: 12 mm 40 mm P 8 mm
Homework #6 Problem 1. A steel alloy core is bonded firmly to the copper tube to form the shaft shown. The materials have the shear stress-strain diagrams are shown in the figure. a) If the total applied torque is 15 kN.m, determine the torque resisted by the core and tube. b) What is the maximum elastic torque that can be applied to the shaft? What is the corresponding maximum shear strain in the shaft? c) What is the maximum torque that one can apply to the shaft? 100 m 60 mm +(MPa) 180 450 mm 15 KN-m 0.0024 (MPa) Steel Alloy 36 0.002 Copper Alloy (rad) y (rad)
X Your answer is incorrect. An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 620 mm. The cross-sectional dimensions of the beam are b1 = 39 mm, d1 = 82 mm, b2 = 23 mm, dɔ = 23 mm, and a = 8 mm. For this material, the allowable tensile bending stress is 20 MPa, and the allowable compressive bending stress is 12 MPa. Determine the largest moment M that can be applied as shown to the beam. b2 a d2 y A B b1 Answer: M = 412.360 N•m Attempts: 2 of 3 used