1. Define stress and state its uits 2. Define divet normed stress Exphin the difference between Compressive stress 3. and tensile Stress Define direct Shear stress s. Compute the Stress ina round bar Subjected to adirect tinsile force of 3200N if the dinmeter af the bar is s lo mm.

1. Define stress and state its uits 2. Define divet normed stress Exphin the difference between Compressive stress 3. and tensile Stress Define direct Shear stress s. Compute the Stress ina round bar Subjected to adirect tinsile force of 3200N if the dinmeter af the bar is s lo mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cast ALuminum cylinder o f a portable hdrauli c riveter is 208 mm in ddiameter The pressure. of The luid petermine Sui table thickness is 15,8 NImm2 by gauge. f the Cylinder wall assuming that the ield Point stress 442 N/mm2 And factor of safety of 6.2 Calculate. the tangential and radial stresses middle radius and at the inner outer surfa ce.
TDe tuláaiceicilaal, D. ile e 200e ticioddocidcICIdCies he sim Ang 2. Fin sile wrl imd tlaeide hrety- 5. JAns. 3 mm) 3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2. Take JAns. 6.25 mm] maximum tensile stress for cast iron as 14 MPa. fIm and is to be subiected to an internal pressure of 2.75
The state of stress at a point under plane stress 40 MPa, Oyy condition is Ox = = 100 MPa and Txy 40 MPa. This radius the Mohr's circle representing the given state of stress in MPa is:
P= 200 lbs |=2" T 250 in-Ibs Qt. DRAW STRESS STATES いITH A SQLARE ECEMENT エN xY AXES Label with stress values Q2 DRAW MOHR'S CIRCLE AT A Q3.CALCULATE PRINCIPAL STRESSES AND DRAW THE PLANE FoR ri$ a IN THE SCHEHATIC Draw element rotated to principal planes and label with stress values and rotation angle
Calcuate torsion From Point A to Point C, Calcuate Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Consider the plane stress element shown in representing the state of stress at a material point. If the magnitudes of the stresses are such that ox 210 Pa, oy = 110 Pa, and = - Txy = 70 Pa, calculate the magnitudes of principal stresses oj and 02, and the maximum shear stress, Tmax, generated at %3D this material point. (a) Record here the the positive of the two principle stresses. (b) Record here the the negative of the two principle stresses. (c) Record here the the maximum shear stress. Tyz Oy
Consider the 2-D state of stress shown below. Using the provided scales graph the Mohr's Circle for the 2-D state of stress with “full" details II-Obtain the Principal Stresses, the Maximum Shear Stress, and complete the table below III- Draw the Planes of Principal and Maximum Shear Stresses in the space provided below Provide "full" details and Use 3 Sig. Fig. in this problem Oy = 15 Ksi Tcw > S y Ox =10 Ksi Тух 5 Ksi 10 5 -20 -15 -10 5 10 15 20 5 10 Tccw > S' O Avg. TMax. 01 02 Op1
Calcuate Torsion and Bending From Point A to Point B and Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Calcuate Torsion From Point A to Point C and Bending from Point A to Point B and from Point A to Point C. Draw a FBD from point A to point B and another for point A to C indicating what stresses are been calculate. Use the stress tensor and stress cube to Indicate what forces are acting at point A. Force apply at point B is 70lb Distacen from Point A to B is 12 in or 1 feet long Distacen from Point A to C is 3 in Handle diameter 0.625 in
Q2 A tensile test specimen having a diameter of (10 mm) und a page length of (S0 mm) was tested to fracture The stieisitrain curve from the tensiotn test is shown in Figure (9) The lower plat is the expanded tegion OAT and associatod with the strain valuns tiven on the lower scale Determine, 480 Lpper veile AB 241 Loser scale + The ultimaie stress, be The propotional limit, 120 e The fracture strees 4 The modulus of elasticity, OAK 0.04 0.0s 0.00 0.12 0.16 1.20 0K2 DANN 0.006 0.008 0.010 e T'he offiet yield stuen at 0.2%, Strain tmm/um) G The asial force ucting on the specireni whert t i uxtended by Figuie (3) a sans
Delermine the orientation of principal planes af stress. Express your anewers ualng three significant figures eeparated by a comma. 8, ,- 19.3,72.24 Submit Prevlous Ancwere Requect Ancwer X Incorrect; Try Again; 3 attempts remaining Part C Determine the maximum in plane shear stress. Express your anawer to three slgnificant figuree and Include the approprlate unit Tmax in-plane 19.2 ksi Submit Previous Ancwers Correct Part D Determine the average normal stress. Express your anBwer to three slgnificant figuree and Include the approprlate unit Owg -15.0 ksi Submit Previous Ancwers Сorect • Part E Figure O 1 of 1 Delermine the orientation of the planes of maximum in plane shear stress. Express your anewers ualng three algnificant figures separated by a comma. ? 30 ksi Submit Requect Ancwar 12 ksi Provide Feedback
you can provide handwritten solution also. At a point in a material under stress, the intensity of the resultant stress on a certain plane is 60 N/mm2 (tensile) inclined 30o to normal of that plane. The stress on a plane at right angle to this has a normal tensile component ofintensity 40 N/mm2.Using the Mohr’s circle calculate, resultant stress on the second plane, the principal planes and stress, plane of maximum shear and its intensity.