Q4: Answer the following questions:1. Clear the memory location ALPHA using data transfer instructions.2. A Data segment is to be located from 60200H to 6FFFFH, what is the value must beloaded in to DS register?.3. Find the content of AX and DX registers after executing the following assembly codesMOV AX, FF82HMOV DX, 33ҒАНCMP AX, DX4. Set the MSB and LSB of CL, leaving other bits unchanged.

According to our guidelines we solve first one: Answer 1:…

Answered: 1. Clear the memory location ALPHA…

Engineering

Computer Science

1. Clear the memory location ALPHA using data transfer instructions.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Answer the following questions: ( 1. Clear the memory location ALPHA using data transfer instructions. 2. A Data segment is to be located from 60200H to 6FFFFH, what is the value must be loaded in to DS register?. 3. Find the content of AX and DX registers after executing the following assembly codes MOV AX, FF82H MOV DX, 33FАН CMP AX, DX 4. Set the MSB and LSB of CL, leaving other bits unchanged.
In the Intel 8086 microprocessor, suppose the register AX contains the data 35AB H. What will be the contents of AX after executing the following programs? Assume that the initial content on the Carry Flag (CF) is one for all the calculations. You MUST clearly show ALL your steps in obtaining your final result for getting full and/or partial credit. Please present your final result in Hexadecimal format. (a) MOV CL,04H SHR AX,CL RET (b) MOV CL,04H RCR AX,CL RET
"uppose we have the instruction Load 500. Given that memory and register R1 contain the values below: Memory Ox100 Ox600 R1 Ox200 Ox400 Охз00 ОхБ00 Ox 100 Ох600 Ox500 Ox700 Ох800 and assuming that Ra is implied in the indexed addressing mode, determine the actual value loaded into the accumulator and fill in the table below: Mode Value Loaded into AC Immediate Direct Indirect Indexed
i need the answer quickly
Question 6 Assume the following registers contents: Find the shortest sequence of ARMv7 instructions that extracts bits 16 down to 11 from register RO and uses the value of this field to replace bits 31 down to 26 in register R1 without changing the other 26 bits in register R1. While the values of RO and R1 don't matter, you might consider RO to be Ox00000000, and R1 to be OxFFFFFFFF. Easy to do this in 4 or 5 instructions. BUT flexible operand 2 allows this in 3 instructions!
The following tables contains memory dump and contents of few registers, as follows: add cont reg cont OXAO Ox72 eax 0x9C Ох9C Оx23 есх Ох11D Ох9Е Ох11 edx 0x40 OXA2 Ox41 After executing the following assembly line lea edx, [eax] The destination is ---- and its contents is Select one: а. еax, Ox 9C b. edx, Ox 23 C. edx, 0x 9C d. eax, Ox 23
This question assumes the machine architecture at the right. Note the stack pointer register, SP, is not part of the register file. SEL is a multiplexor used to select one of the inputs to the ALU. Assume memory addresses require only one memory cycle to fetch or store (unlike the 68000). MAR Register File (RO-RI5) MDR Show the machine code control IR constants sequence of an instruction that will set a block of from 1 to 127 memory locations to zero. The size of the block is in RO and the address of the block is in R1. Assume the instruction fetch sequence is the same as in Question 4 and start with the next step. R0 and R1 can change in the execution of the sequence. SEL PC SP ALU TEMP Status
6. An AJMP instruction is in memory locations 1A24H and 1A25H. The label of this instruction will be directed begins in memory location 18B6H. How can be the destination address encoded? Hint: the opcode for AJMP instruction is 01H. M 9. 8. Illustrate two ways to transfer the content of the accumulator to internal RAM address 3FH.
Write a PIC18 instruction sequence to initialize the contents of file registers at addresses from 0x077 until 0X07A with the value D'120'. You MUST use indirect addressing mode with file select register, FSR2 in your solution.
Describe the modifications to the single clock cycle datapath that would be needed to implement the jalr instruction (jump and link register – see page A.672 of the text), and give the control signal settings that would be required for this instruction.
Pls send me solution fast within 5-10 min and u will rate instantly.... Solution must be in typed form.... 1. Write the following swap function to the IA-32 architecture assembly code and save it in a swap.s file. Call the swap function in the main function to test your assembly code, and write the main function in a main.c file. To compile, gcc -o swap.exe main.c swap.s. 2.Give the final memory images after the operation, answer the following questions: What’s the memory address of your swap function? Which register holds the initial value *xp? Which register holds the initial value *yp? What are the memory addresses of the two locations pointed by xp and yp? Write your answer to report. Write an assembly function to calculate a polynomial as: n = ax^2 + bx + c If x = 2, a = 2, b = 3, and c = 5, the function should return. 4 × 2^2 + 3 × 2 + 5 = 27 The prototype for the function should be: int poly(int x, int a, int b, int c). Write the assembly code in a poly.s file and a main…
Please solve