1. Clear the memory location ALPHA using data transfer instructions. 2. A Data segment is to be located from 60200H to 6FFFFH, what is the value must be loaded in to DS register?. 3. Find the content of AX and DX registers after executing the following assembly codes MOV AX, FF82H MOV DX, 33FAH CMP AX, DX 4. Set the MSB and LSB of CL, leaving other bits unchanged.

1. Clear the memory location ALPHA using data transfer instructions. 2. A Data segment is to be located from 60200H to 6FFFFH, what is the value must be loaded in to DS register?. 3. Find the content of AX and DX registers after executing the following assembly codes MOV AX, FF82H MOV DX, 33FAH CMP AX, DX 4. Set the MSB and LSB of CL, leaving other bits unchanged.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Q7M4
For the given x86-64 instruction, list the following for each operand: • location of operand (register, memory, or immediate) • size of the operand in bytes • addressing mode of the operand 9. addq $5, %rax 10. subw -8(%sp), %cx 11. movl (%esi), %edx 12. movb %cl, 8(%esp) 13. addw 6(%ebx, %eax, 4), %si
Question 1: Use Indirect addressing to write a PIC24 assembly code that complements and adds 5 and multiply by 2 to 1024 data bytes into the memory at starting address 0x1000. The original data are stored in the memory starting from address 0x800.
(b) Construct a sequence of instructions such that (i) you add the 8- digit BCD number in AX and BX to the 8-digit BCD number in CX and DX. (AX and CX are the most significant registers. The result must be found in CX and DX after the addition.). (ii) Then logically shift AX right by 12 bit positions and the rightmost 12 bits of BX into the leftmost 12 bits of AX using double precision shifting. (iii) Assuming that DL= 0F3H and BH=72H , compute the answer after BH is subtracted from DL and show the contents of the flag register bit
Section [error correction and detection] 1 of3 Upload answer sheets Design a decoder which selects the register files of a processor where it has registers from R0 to R15. Assume a 8-bit data word 11011001 is stored in memory. Using an appropriate technique determine the error check bits that would be stored in memory along with the data word. During memory read operation, a LSB (Least Significant Bit) gets modified. Explain how does the technique correct the error? uolcuour suhmission
Develop the assembly code for the following: Load 10 Hex values in 10 memory location. Next find the sum of all the values loaded in the memory location. At the end Register A should contain low byte and Register R5 High byte of the final result.
Determine the new contents of BX and the carry flag after executing the following instruction RCL BX, CL; BX=FFB1H, CL=3, and CF=1
Datapath for the LDI Instruction 7 Recently we have been discussing the importance of the datapath and its relationship to the Register Transfer Notation and control signals need to execute instructions in the datapath. Answer the following questions about this specific What is the ML (or binary instruction) of this single instruction? Give your answer in hexadecimal. instruction: type your answer... LDI R4, data Where the label data is at address x3005, and the LDR instruction is at address x3000. What is the Register Transfer notation for this instruction? Remember to change the destination and source registers to the actual registers of the instruction. type your answer... List in order all the controls signals required to execute this instruction. You do not need to list the signals for fetching and decoding the instruction.