1. A standard L8×4×½ is used as a tension member. The bolts are 1/2" diameter in standard holes. Considering the yielding and rupture limit states, calculate the factored capacity. 2.5"| 4.5" 2" 3" 3" tatalal

1. A standard L8×4×½ is used as a tension member. The bolts are 1/2" diameter in standard holes. Considering the yielding and rupture limit states, calculate the factored capacity. 2.5"| 4.5" 2" 3" 3" tatalal

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A 1 ⁄2 × 5-inch plate of A588 steel is used as a tension member. It is connected to a gusset plate…

A: Given: 1⁄2 × 5-inch plate of A588 steel. ⇒Width, b=12in⇒Thickness, t=5 in Diameter of bolts = 5⁄8…

Q: A PL ½ x 8 tension member is connected with six 1-inch diameter bolts as shown in the figure below.…

A: Answer We are given Plate 1/2 x 8 bolt diameter = 1 in A36 steel Shear lag factor U = 0.1

Q: Questo j = 1,69" R=2+1" + 'k" 10008 967 5 # 0.5" |d=7.3" Material is ASTM A36. Plate is fixed by 4…

A: Given values: Thickness of tension member, t = 0.5 in Total depth, d = 7.3 in Diameter of screws, db…

Q: 2. A connection is made from two 1.9 cm bolts in parallel, placed on a 21.6 cm wide steel bar. The…

A: Given data:- Diameter of bolts,d = 1.9 cm Thickness of steel bar, t = 2.54 cm Ultimate strength of…

Q: A double-angle shape is shown in Figure 3.5. The steel is A36, and the holes are for…

A: Double angle section is shown in the figure above. Grade A36 steel is used. Diameter of bolts= 1/2…

Q: 3. Determine Rn based on bolt limit states. Slip critical connection is used for design and Grade…

A: sub critical connection Grade- 10.9 M22 Bolts- Class A surface Minimum edge distance and spacing -…

Q: Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is…

A: Given- Properties of WT- 12×38Ag=11.2 in2y'=3.0 inbf=8.99 inA992 steel-fy=50 ksiFu=65 ksiLL=3DL

Q: O Which of the following gives the max. shearing stress if P = 40 kN, e = 45", a = 300 mm, b- 450…

Q: An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g = 75…

A: We will use formula of Net area.

Q: An A36 tension plate is 9 mm thick is given below. Bolts are 20 mm. Given that s = 50 mm and g =…

A: Given data in question Thickness of plate Diameter of bolt Bolt lines Guage distance To find out…

Q: Find the ava shown in the liameter bolts Use LRFI Use ASD 1 2) 3½" I

Q: The tension member shown is an L150 × 87.5 × 8. The bolts are 19 mm in diameter. If A36 steel is…

Q: I Example 2 W SECTION The hanger below (front view and side view) supports a 5000 N partition wall.…

Q: Five bolts are used in the connection between the axial member and the support. The ultimate shear…

Q: The angle L 8 x 8 x ½ in tension shown in the figure below must resist a service dead load of 35…

Q: a 3" oj ob C" OC 5" of od 3" e = 4" A" B" | A" B" A" B" The holes are for 1-inch-diameter bolts.…

Q: SITUATION II: Calculate the permissible tensile load P 50 under the following conditions: Fy3248…

Q: A Channel Cóx13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using…

Q: Question 3) The tension member shown in Figure 1 contains holes for in. bolts. At what spacing, s,…

A: We need to calculate spacing between two bolts.

Q: A bracket shown in the figure 6.9 carries an eccentric load of 30 kN at an eccentricity of 200 mm.…

Q: A plate is fastened to a fixed member by four 16mm rivets arranged as shown. Compute the maximum…

A: To determine the shear stress in the rivets. Given, Diameter of the rivets (d) = 16 mm From the…

Q: miscellaneous channel MC 300 x 67 is bolted as shown on the figure 2.20 by a 0 mm diam. bolts. A 36…

A: Area of section, Depth, Thickness of web, Flange thickness, Width of flange, To find: (a)…

Q: Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The…

A: We know that Maximum factored LRFD tensile force capacity of the member is given by minimum of the…

Q: A vessel flange uses 16 2 in. diameter bolts. Flange stress calculations indicate that a flange…

A: Given data Diameter of bolts=d= 2 in Flange thickness= t= 4.5 in Bolt circle diameter = C= 22.5…

Q: cd efgh O ij klmn u op V q 0 k i What is the line for which the section will rupture in tension? All…

Q: The tension member shown in the figure is connected to a gusset plate as shown with 1.2-inch…

Q: A D E 1.H Section 2. Wide-Flange 3. American Standard 4. Unequal Leg Angle 5. C Section 6.T Section…

A: Matching the cross section

Q: A hole 12 mm diameter is to be punched through a plate 18 mm thick. If the shear strength of the…

A: Diameter of hole d=12 mm and is punched through a plate 18 mm thick plate thickness t= 18 mmthe…

Q: Problem 1. The tension member is a PL 6 x 1/2. It is connected to a 3/8-inch-thick gusset plate with…

A: Answer Given in the Below attachments

Q: Determine the effective net area of the tension member shown in the figure. 000 3"3" L6 x 6 x ½…

A: Given Data- Diameter of Bolt = 3/8 in Find - Calculate the effective net area of the member ?

Q: For the bolted tension member is shown in the figure. Determine the effective area,

A: Compressive stress is the force that deforms the material in a way that reduces the volume of the…

Q: Determine the smallest net area of the tension member shown in the figure. The holes are for 3/4-in…

A: here given double angle sec so please keep this in mind for no. of bolt in net area calculations…

Q: a) Calculate the service shear force applied on the connection. b) Calculate the service tensile…

A: Given data: Section of tee bracket = WT 6*32.5 is attached to a column flange Section of column =…

Q: Problem #3 A 16 mm thick tension member is connected by two 6.25 mm spliced plates as shown. The…

Q: A's As,web As bw Materials: C25/30 / B420C Longitudinal reinforcements A's=2 $ 14 As,web= 2 0 12 A₁=…

A: To find- Reinforcement ratio and failure type of beam

Concept explainers

Connections

In steel structures, connections are the members that join two or more steel members. The connections are the most important members of any steel structure, and hence, they are designed more carefully. The majority of the construction cost of steel structures is incurred due to the connections. The design of connections is done as per the recommendations and specifications of the American Institute of Steel Construction (AISC).

Question

1. A standard L8×4×½ is used as a tension member. The bolts are 1/2" diameter in standard
holes. Considering the yielding and rupture limit states, calculate the factored capacity.
2.5"| 4.5"
2"
3"
оо
3"
tatalal

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

how to solve ?? please and thank you.
An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of hole = 22mm. Properties of 150 mm x 100 mm x 12.5 mm angle A = 3065 mm2 y = 50.55 mm Fy = 248 MPa Fu = 400 MPa Determine the desire strength due to fracture in the net section. Use U = 0.85 kN
SITUATION I A lapped bolted lension member is shown. Diameter of bolts are 22 mm and the plate material is A36 steel Fy = 275 MPа, Fи 3 415 МPа. Assume the fasteners are adequate and do not control the tensile capacity. Diameter of hole is 2.5 mm bigger than the diameter of bolt. 12 :: 350 50 100 100 50 50 1. Determine the tensile capacity of the lapped joint based on gross area. a. 252.656 kN c. 866.250 kN b. 202.125 kN d. 693.000 kN 2. Determine the net Area for the tensile capacity of the lapped joint. а. 3318 тm? c. 5250 mm? b. 1554 mm? d. 1824 mm? 3. Determine the tensile capacity of the lapped joint based on the net area. a. 752.856 kN C. 866.250 kN b. 688.845 kN d. 1039.500 kN
PL 5/8 x 12 3/4-in-diameter bolts
Material Strengths: Fy = 248 MPa, F = 400 MPa For the two lines of bolt holes, the pitch is the value that will give a net area DEFG equal to the one along ABC. The diameter of the holes is 22 mm. The thickness of the plate is 12 mm. Determine the LRFD design tensile strength based on yielding on gross area. D A to 50 1 ÓB 50 50 ic O 410 kN O 464 kN O 446 kN O 401 KN F IG Pitch Pitch KISS|Y
An A36 tension plate is 10 mm thick is given below. Bolts are 20 mm. Given that s = 65 mm and g = 70 mm, calculate the net area at tensile fracture line d-e-b-f-g in mm2. Write your answer rounded to the nearest whole number.
Please answer with complete details. Thank you. A = 1 B = 1 C = 2
Determine the allowable strength of the figure as shown
1. The tension member shown in Figure 3.4-2 is a PL 58 x 10, and the steel is A36. The bolts are 3/4-inch in diameter. a. Draw the different potential failure lines. b. Compute the effective net area. 22" 2½" 2" 4 3" *₁ 3" ✓ 2" 2. A double-channel shape, 2C10 x 20 steel, Fy = 50 ksi and Fu = 70 ksi, is used for a built-up tension member as shown in the figure. The holes are for 12-inch-diameter bolts. PNA a. Determine the design strength for LRFD. b. Determine the allowable strength for ASD. YD Shape A 2" 2" -X Area, Depth, d | 3²²-|-1 3²² | 00 "There is no elevator to success, you have to take the stairs." - Zig Ziglar God bless. Ⓒ O O O Web Thickness, tw in. in. O 4" C10-30 x25 x20 5.87 10.0 10 0.379 % x15.3 4.48 10.0 10 0.240 4 4" Table 1-5 C-Shapes Dimensions Flange Width, b₁ 2 in. in. in.2 in. C15x50 14.7 15.0 15 0.716 1168 3.72 3% 0.650 % x40 11.8 15.0 15 0.520 x33.9 10.0 15.0 15 0.400 % 14 3.52 32 0.650 % %/16 3.40 3% 0.650 % C12-30 8.81 12.0 12 0.510 4 3.17 3% x25 7.34 12.0 12…
7. Determine the design tensile strength of the plate (200 x 10 mm) connected to 12 mm thick gusset, using 24 mm bolts as shown below. Use A572M Grade 345 steel materials. 200 40 50 40 30 30 30 30 40
Give me right solution according to the question...