Design a lightest single angle tension member with the following requirements: Dead Service Load = 40 kips, Service Live Load = 66 kips ● Length = 20 ft ● ● ● Steel A36 Bolt Pattern Below Check Block Shear and Slenderness

Q: Course: Quality Engineering How to explain all of the ISO 9000 in a structured way.

A: ISO 9000 certification ISO 9000 consist of a set of international standards on quality management.…

Q: change would you suggest to execute this design? 3.19 A section of a road has a superelevation of…

A:

Q: How is ThOD solved?

A: THOD  Theoretical oxygen demand (ThOD) is the calculated amount of oxygen required to oxidize a…

Q: Explain the principle of 5S in Construction. Complete the answer please.

A: Introduction- Construction- It refers to the methods and business associated with assembling and…

Q: show the integration process

A: To show the integration process

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: Give at least 3 examples of value engineering that applies in a construction of civil engineering…

A: Here we have to give atleast 3 examples of value engineering that applies in a construction of civil…

Q: What are the benefits and drawbacks of beginning a project using a pre-built model vs a clean sheet…

A: Benefits of Beginning a Project with a Pre-Built Model: 1. Cost Savings: Using a pre-built model can…

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS & GNSS surveys.

Q: What are Cole values

A: Solution: COLE stands for The Coefficient of linear Extensibility.  It is used to measures the soil…

Q: What is a box model? Give the equation to represent box model.

A: The Urban air quality models has been called box models. The Figure is a schematic graph of a box…

Q: The solution came out all in one line. Making it difficult to understand. Please Can it be written…

A:

Q: 10 25k 10'

A: The below cantilever beam is given;

Q: 22-ENGINEERING MANAGEMENT 4. As an engineer manager, how will you manage committees effectively?

A: an engineer manager, following method we would apply for  manage committees effectively :

Q: where did you get 6?

A: 6 is the loading intensity at B.

Q: Construct a Project Charter of Construction Project. Be specific and SIMPLE.

A: A construction project charter includes the following details: 1. Overview of the project 2. Project…

Q: What does the reductent diagram look like?

A: What does the reductent diagram look like?

Q: What is CAD? Explain.

A: CAD-Computer-aided design is a way to  create 2D drawings and 3D models of real-world products…

Q: Give an actual example of a scenario (in civil engineering practice) where an honorarium is given to…

A: An honorarium is a contribution paid ex gratia, that is, without the presenter acknowledging any…

Q: 2 unsafe acts and unsafe conditions associated with ergonomics and psychological hazards in…

A: Solution- Electrocution, falls from large heights, damages from tools, equipment's, and machine,…

Q: Add/Sub the following rational functions. SHOW YOUR WORK IN THE ANSWER BOX x + 2 x + 5 x2 + 6x +5 2]

A: Hello dear this is the solution of your problem Please see the attached solution, thanks

Q: Quality Engineering question A Production Engineer working in Company A wants to maintain a…

A: Introduction- The standard operations procedures  is a series of step-by-step procedures established…

Q: some examples of the term OFFSET

A:

Q: can you reorganize this please? Its a bit confusing to read and understand

A: Given data ,  water content = 45% The density of the solid particles  = 2500 kg/m3   To find out the…

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: How is the dimension paper used to compile an accurate Bill of Quantities??

A: Dimension paper is used in taking off which refers to the process which identifies elements of…

Q: orry I cannot understand can u pls write it down？

A:

Q: Can you please explain where all the values came from?

A: Theoretical oxygen demand (ThOD) is indeed the estimated quantity of oxygen needed to completely…

Q: What are Quantity Variations?

A:

Q: What is Micropiles?

A: - A Micropile is a type of friction pile having diameter less than equal to 305 mm which can be…

Q: Hello! Would it be possible to included a step by step solution without skipping something and add…

A:

Q: Define each term in three sentences only. 4. Curve Resistance 5. Air Resistance 6. What is AASHTO?…

A: (4.) Curve Resistance - * It is the loss of tractive force when a rear wheel     driven vehicle…

Q: What do you mean by allowances and tolerances in specifications?

A: Tolerance and allowance are two important terms which are used in specifying the dimensions of any…

Q: Directions: You are an architect in a constructiorn company. You are tasked to build 3 circular…

A: As mention above the the diameter and length of three circular tank are or we can say that capacity…

Q: how many different ways are there to arrange six people in a round table?

A:

Q: Give the functions of each parts of a transit in your own words and understanding. Please do not…

A: A theodolite is a tool used to measure horizontal and vertical angles.

Q: Give example from any organization in civil engineering professional

A: Organization in civil engineering professional are; (ASCE) is the full form of American Society of…