. A cylindrical bucket 60 cm in diameter and 50 cm high weighing 150N contains oil (s=0.80) to a depth of 20 cm.(1) Determine the combine weight of bucket and oil.(2) When placed in water, what will be the depth to the bottom of the bucket?(3) What is the maximum volume of oil in liters the bucket can hold and still float?

Answered: 1. A cylindrical bucket 60 cm in…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fluid mechanics
Problem 9.123 Determine the magnitude of the resultant hydrostatic force acting on the dam and its location, measured from the top surface of the water. The width of the dam is 8 m P = 1.0 Mg/m³. (Figure 1) Figure 1 of 1 6 m Part A Determine the magnitude of the resultant hydrostatic force acting on the dam. Express your answer to three significant figures and include the appropriate units. F= Submit Part B h = μA Submit Value Determine the location of the resultant hydrostatic force acting on the dam, measured from the top surface of the water. Express your answer to three significant figures and include the appropriate units. Units My Answers Give Up μA Value Units ? My Answers Give Up ?
Problem 9.123 Determine the magnitude of the resultant hydrostatic force acting on the dam and its location, measured from the top surface of the water. The width of the dam is 8 m P = 1.0 Mg/m³. (Figure 1) Figure 1 of 1 6 m Part A Determine the magnitude of the resultant hydrostatic force acting on the dam. Express your answer to three significant figures and include the appropriate units. F= Submit Part B h = μA Submit Value Determine the location of the resultant hydrostatic force acting on the dam, measured from the top surface of the water. Express your answer to three significant figures and include the appropriate units. Units My Answers Give Up μA Value Units ? My Answers Give Up ?
Problem 9.123 Determine the magnitude of the resultant hydrostatic force acting on the dam and its location, measured from the top surface of the water. The width of the dam is 8 m P = 1.0 Mg/m³. (Figure 1) Figure 1 of 1 6 m Part A Determine the magnitude of the resultant hydrostatic force acting on the dam. Express your answer to three significant figures and include the appropriate units. F= Submit Part B h = μA Submit Value Determine the location of the resultant hydrostatic force acting on the dam, measured from the top surface of the water. Express your answer to three significant figures and include the appropriate units. Units My Answers Give Up μA Value Units ? My Answers Give Up ?
Q 1 A
please write big and legible, my eyes can't see well
In a system, an open cylindrical steel tank, which has a density of 7820 kg/m^3, has an inside diameter of 4.0 m and an internal height of 5.0 m. From being initially empty, exactly 2,582.13 slugs of water were poured into the tank. Next, another liquid mass, equivalent to 1,626.742 slugs, was poured inside the tank. After settling, this fluid occupied three-tenths of the total internal height of the container. Then, mercury was poured into the tank. After the fluid has settled, the height of the mercury layer was measured to be one-fifth of a meter. Finally, oil, with S.G.=0.80, was poured to fill the remaining empty volume of the tank. 1) Draw the vertical profile of the tank and label properly all the liquid layers, indicating properly the value of specific gravity used for each liquid layer. 2) What is the total mass of the system if the tank itself has a volume of 2.29 m^3? 3)Solve for the hydrostatic gage pressure at the liquid surface, at the interfaces between any two…
ASAP dont round off initial values, round off final ans only pls ty
Refer to the picture below to solve the following problems
1. A nurse applies a force of 4.40 N to the piston of a syringe. The piston has an area of 6.56 x 105 m². What is the pressure increase in the fluid within the syringe? kPa
The water tank has a diameter of 750mm , a height of 1750mm to which the Initial height of water was 5 cm. If water was to be filled 90% of height and the water meter initial reading is 2000L, a. what is the final reading of the water in L b. Find the mass of water tank if its initial weight is 45 kg

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS