Determine the magnitude of the resultant hydrostatic force acting on the dam and its location, measured from the top surface of the water. The width of the dam is 8 m P = 1.0 Mg/m³. (Figure 1) Figure 1 of 1 6 m Part A Determine the magnitude of the resultant hydrostatic force acting on the dam. Express your answer to three significant figures and include the appropriate units. F= Submit Part B h = O _ Submit μA Value Determine the location of the resultant hydrostatic force acting on the dam, measured from the top surface of the water. Express your answer to three significant figures and include the appropriate units. Units My Answers Give Up μA Value Units ? My Answers Give Up ?

Determine the magnitude of the resultant hydrostatic force acting on the dam and its location, measured from the top surface of the water. The width of the dam is 8 m P = 1.0 Mg/m³. (Figure 1) Figure 1 of 1 6 m Part A Determine the magnitude of the resultant hydrostatic force acting on the dam. Express your answer to three significant figures and include the appropriate units. F= Submit Part B h = O _ Submit μA Value Determine the location of the resultant hydrostatic force acting on the dam, measured from the top surface of the water. Express your answer to three significant figures and include the appropriate units. Units My Answers Give Up μA Value Units ? My Answers Give Up ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pls answer all question, you'll get a like ty. Dont round off initial values, round off final ans only plz ty
SHOW COMPLETE SOLUTION AND SKETCH THE ILLUSTRATION A cylindrical tank 6.7 m in diameter is made from steel plates that are 12 mm thick. Find the maximum height to which the tank may be filled with wine with density 720 kg/m3 if the circumferential stress is limited to 41.4 MPa.
5........ 2 decimal places for the answer
2. A line load of q per unit length is applied at the ground surface as shown in the Figure below with a polar system: Given q = 145kN/m, calculate stresses (or, 0e, Tre) at r=10 m and 8= 30° q/unit length de ●P(-8) 09 Tax = Tro
A concrete dam retaining water is shown in the picture. If the specific weight of concrete is 23.5 kN/m3 , 2. Find the maximum intensity of pressure? 5. Find the resultant force? 7. Determine the minimum intensity of pressure?
Problem 1 A spherical gas tank has an inner radius of r = 1.5 m. Part A If it is subjected to an internal pressure of p = 210 kPa, determine its minimum required thickness if the maximum normal stress is not to exceed 12 MPa. Express your answer to three significant figures and include the appropriate units. ANSWER: t =
Determine the resultant of the three forces acting on the dam as shown in the figure below.
3. Flownet shown below, dimensions in meters. Point A is located 12m below the base of the dam. Calculate the pressure head at point A. Show your work and circle your answer. 45.0 3.0 12.9 20.0 m 5.0 TUT -1.0 10 A 9 DATUM m 34.0
Q2 Oil (s.g = 0.761) flows from tank A to tank E, as shown in the figure(2). Lost head items may be assumed to be as follows: A to B = 0.6 ; B to C = 9 ; C to D = 12 2g 2g 0.4;D to E = 9. Find the flow rate and the pressure at C. 2g Figure (2)
The pressure gage in the experimental setup shown below shows a pressure of 100 kPa. Determine the total head, elevation head and pressure head at all points indicated on the figure below. Show all your calculations AND report your results in the table below. (Hint: Y, = 10 A 3 m -Soil B. 3 m D 1.5 m Datum
Instruction: Follow Given-Required-Solution format for your computation. Complete FBD for full credit. Problem: The figure shows the water pressure acting on the sides of a dam that is 20-m long. Determine the resultant force of the water pressure acting on the dam.
Please answer correctly and box the final answer