1. A building exhaust fan for a large commercial building weighs 180 pounds and operates at a speed of 600 rpm. Due to manufacturing tolerances, it may have a rotating imbalance. It is desired to limit force transmissibility to 2.5 as the fan passes through resonance during startup and wind-down. In addition, an Isolation of 90% is required at the operating speed of the fan. The fan's framework will be supported from the floor at 4 corners. Design, select, and specify vibration isolators at the four corners. It is acceptable to assume the center of gravity is symmetrical with respect to all four corners, enabling you to treat this as a single DOF system without pitch or yaw.

1. A building exhaust fan for a large commercial building weighs 180 pounds and operates at a speed of 600 rpm. Due to manufacturing tolerances, it may have a rotating imbalance. It is desired to limit force transmissibility to 2.5 as the fan passes through resonance during startup and wind-down. In addition, an Isolation of 90% is required at the operating speed of the fan. The fan's framework will be supported from the floor at 4 corners. Design, select, and specify vibration isolators at the four corners. It is acceptable to assume the center of gravity is symmetrical with respect to all four corners, enabling you to treat this as a single DOF system without pitch or yaw.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

NOTE: Do not solve the whole numerical.I only want the simplified schematic diagram of the plant showing all the necessary data displayed on it.
As8
An engine of 175 mm bore and 375 mm stroke is governed by hit and miss type governor to 220 rpm. With a fixed setting of the gas supply and ignition advance, indicator diagrams gave the following values of mean effective pressure. Firing, positive loop 5.7 bar, negative loop 0.25 bar; missing negative loop 0.42 bar. When developing 6 kW the explosions were 100 per minute and the gas used was 0.1 m per minute. Calculate the friction power and assuming uniform gas supply per explosion, find the gas consumption per minute at no load.
can you please find the solution question no:29
A thin rod 5 mm diameter is held between two chucks 0.8 m apart and deflects 0.5mm under its static weight. The rod weighs 1.508 N/m and the flexural stiffness is 6.136 N m². Calculate the lowest critical speed in rpm taking into account the distributed mass
I need answers to parts 13, 14, and 15, pertaining to the print provided.
Chapter 20 : Ducts 697 damper resistance necessary to give the required flow when the static pressure in the main duct before off-take is 10 mm of water. If the branch pieces are placed 12 m apart along the main duct, calculate the required percentage static regain in the main duct across the off take shown in order that the static pressure in the next off take will be 10 mm of water also. The dynamic loss coefficient for the branch, 90° bend and exit grill may be taken as 0.65, 0.3 and 0.8 respectively. (Ans. 9.94 mm of water; 66.2%) 9. An air duct system is provided as shown in Fig. 20.29. The standard air enters at point A with a static pressure of 12 mm of water. 30 m 15 m 15 m. 30 m 60 m 22.5 m Fig. 20.29 The branch BE delivers 60 m/min at E, branch CF delivers 180 m'Imin at F and the main duct delivers 240 m'/min at D. Using equal pressure drop method, find the duct dimensions. Assume free exit at each outlet. [Ans. Dan = 1 m; Duc = 0.9 m: Den = 0.75 m; Dag = 0.375 m; De =0.55 m]…
quick pls
The image and dimensioned drawings below depict a steel drawb ring with a 100,000-1b towing capacity rating. The drawbar ring is fastened to a 0.75-inch thick steel drawbar coupler plate using four 7/8"x9 hex head bots and regular hex nuts. Determine the SAE bolt grade necessary to ensure a load factor to overproofing of at least 2 (for the rated towing capacity) where the bolts are pre-loaded for reuse. You can neglect any shear loads imposed on the bolted assembly. 0.71in 6.83in 3in 1.62in Ring ID Lo,9tin 6.39in 4.5in 4.5in 6.61in
BOOK: FLUID POWER, 3e, JAMES A. SULLIVAN PROBLEM: 13 - 18