9:49 :lProny Brake Length = 36"%3DFuel Consumption = 7.5 GPH%3DFuel Type = 10OLL100LL burns at 20,000 BTUSLiberty L-12Calculate:• Piston Displacement• Total Displacement• Indicated Horsepower• Brake Horsepower• Torque• Compression Ratio• Mechanical Efficiency• Thermal EfficiencyThe specifications are as follows:Liberty L-12 12-cylinder engine.Bore = 5"Stroke = 7"Total Volume per cylinder = 151.07 in3Indicated Mean Effective Pressure 131 PSIRevolutions per minute = 1650Prony, Brake reading = 384.9 lbsPreny, Brake Length = 42"Fuel Consumption 33 GPH .%3DFuel Type = 10OLL%3D100LL burns at 20,000 BTUSH8 7916759 (1773}||

Answered: Image /qna-images/answer/1ecc4a73-8d48-49e8-88fd-398e542bb0be.jpg

Liberty L-12 Calculate: • Piston Displacement • Total Displacement • Indicated Horsepower • Brake Horsepower • Torque • Compression Ratio • Mechanical Efficiency • Thermal Efficiency The specifications are as follows:

Liberty L-12 Calculate: • Piston Displacement • Total Displacement • Indicated Horsepower • Brake Horsepower • Torque • Compression Ratio • Mechanical Efficiency • Thermal Efficiency The specifications are as follows:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hydro Tasmania has initiated the Battery of the Nation (BotN) strategic initiative to investigate and map out future development opportunities for the State of Tasmania to make a bigger contribution to a future National Electricity Market (NEM). The Tarraleah scheme redevelopment pre-feasibility study was undertaken through this initiative, with funding support from ARENA under the Advancing Renewables Program. For this assignment problem you will be using your knowledge of hydro power to: (1) estimate extended specifications for a new power station on the left bank of the Nive River opposite the existing power station; and (2) to reverse engineer specifications for the Pelton turbines currently installed at the Tarraleah power station. The pre-feasibility design team established basic parameters of a new power station to comprise two Francis turbines with a design flow of 20 m³/s (total 40 m³/s), a net head of 305 m and an installed capacity of ~57 MW (total 113 MW). The Tarraleah…
As a mechanical engineer, you were asked by your supervisor to monitor the operation of 4-stroke engine; as a result you got the following readings: > Imep = 780 kN/ m2 > Engine speed = 800 rpm > Brake Power 30 kW %3D %3D > nm = 85 % > B/S 0.7 You noticed also, that the inlet valve opens 10° before TDC and closes40° after BDC and it takes 0.0035 second after ignition for the charge to gain maximum pressure. Depending on the above readings, find the following engine parameters: a. The crank angle when the spark occursfor the maximum pressure to be at TDC b. The time period in second of inlet valve opening during one cycle c. The diameter of the engine d. The average piston speed 1 Upload file
1 The following observations are recorded during a test on a four-stroke petro engine, F.C = 25cc of fuel in 10 sec, speed of the engine is 2600 rpm, B.P = 22 kW, Qair 0.00134 m, piston diameter 90 mm, density of the fuel = 0.85gm/cc , compression ratio = 7.5, CV of fuel = 42000KJ/Kg, room temperature = 24 °C %3D = 140mm, stroke length = %3D %3D %3D 2 A six-cylinder 4-stroke cycle petrol engine is to be designed to develop 250 kW of (b.p) at 2200 rpm the stroke / bore ratio is to be 1.3:1. Assuming nm =80% and an indicated mean effective pressure of 9.5 bar, determine the required bore and stroke. If the compression ratio of the engine is to be 7.5 to 1, determine consumption of petrol in kg/h and in kg/bp.hr. Take the ratio of the indicated thermal efficiency of the engine to that of the constant volume air standard cycle as 0.65 and the calorific value of the petrol as; 44770KJ/kg.
Give your designs in Tables or Graphical format, as appropriate. 1. Given the following parameters, design a vertical heater-treater: Qo = 5,000 bopd API = 36 inlet T = 80 °F Yw = 1.03 2. Given the following parameters, design a horizontal heater-treater: Q. = 20,000 bopd To = 80 °F API = 32 Yw = 1.03
Mechanical Engineering t1 = 90F t2 = -10F Qa = 10,000 BTU/Hr Hp (motor) =? Motor LPF= 95%
plz ansswer q1 part e velocity is in km/h not in m/s
A truck has an engine power of 180 HP and it has empty weight of 3000 kg and the protitable load is 15000 kg. Truck moves 3% in upgrade direction. The engine performance is 0,75, the friction coefficient between the tire and the surface is 0,30 , the Rolling resistance coefficient is 20 kg/t, truck width is 2,40 meters, the height is 2,80 meters, air resistance coefficients is 0,060 and the rear tires are powered. a)Calculate the vehicle speed while climbing the exiting upgrade. b) If the speed of the vehicle is 15 km/h, calculate the upgrade value.
In the United States, electricity is sold using the SI units of kilowatt (kW) or megawatt (MW), and fuel for power generation stations is generally purchased using English units, e.g., British thermal unit (Btu), gallon (gal), and ton. An industrial power plant has an average annual load of 100 MW (electrical). If the overall thermal efficiency is 33% (based on HHV), what is the annual cost of fuel if the plant is fired with (a) natural gas, (b) No. 2 fuel oil, and (c) bituminous coal? Use the data from Tables 2.2, 2.7, and 2.13. Assume the cost of natural gas is $5/million Btu, the cost of No. 2 fuel oil is $3/gal, and the cost of bituminous coal is $60/ton (1 ton = 2000 lbm)
A wind turbine gives the following data: Blade length= 57.5 m. Wind speed = 13 m/s Air density = 1.225 Kg/m3 Power coefficient = 0.45 Assuming equal efficiencies for gearbox and generator, If the Power output from wind turbine, P is 1.9 MW, then find
he performance of the engine depends on inter-relationship between power developed, speed and the specific fuel consumption at each operating condition within the useful range of speed and load. Explain the inter-relationships of the given parameters.
I need answer within 20 minutes please please with my best wishes