Given from a generator: Full-load rating of generator Full-load efficiency of generator : 90% Speed Frequency EMF 70mm 70mm :37.5MW -16 x M42 bolts : 3,600rpm : 60HZ : 13kV 300mm 480mm 580mm From the given data, determine the following: (a) Power transmitted by the coupling; (b) Torque developed in kg-m; (c) Load in the bolts in N; (d) Shearing stress in each bolt; (e) Bearing pressure in each bolt; Turbine Rotor shaft Generator Rotor shaft

Given from a generator: Full-load rating of generator Full-load efficiency of generator : 90% Speed Frequency EMF 70mm 70mm :37.5MW -16 x M42 bolts : 3,600rpm : 60HZ : 13kV 300mm 480mm 580mm From the given data, determine the following: (a) Power transmitted by the coupling; (b) Torque developed in kg-m; (c) Load in the bolts in N; (d) Shearing stress in each bolt; (e) Bearing pressure in each bolt; Turbine Rotor shaft Generator Rotor shaft

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data are available for a belt conveyor design: 1. Conveyor capacity: = 1300 t/h; 2. Belt speed = 1.5 m/sec; 3. Conveyor height = 15 m; 4. Conveyor length = 175 m; 5. Mass of a set of idlers = 15 kg; 6. Idler spacing = 1.2 m; 7. Load due to belt = 25 kg/m; 8. Inclination angle of the conveyor = 10 deg.; 9. Coefficient of friction = 0.05; 10. Start-up factor = 1.5; 11. Drive efficiency = 0.90; 12. Friction factor = 12; and 13. Breaking strength loss factor = 0.80 Determine the following: (1) Belt tension, (2) Load due to idlers, (3) Minimum motor power; (4) Acceleration of the conveyor belt, and the (5) Belt breaking strength.
An industrial fan running at 600 rpm is driven by a 25-kW, 960 rpm, induction motor. The pulley mounted on the motor shaft is 270 mm. Center to center distance is 1.5 meters and use f = 0.35. Determine the minimum angle of wrap in rad.
QUESTION 1 Consider the equations of motion of an armature controlled DC motor given by Jw(t)+bw (t) Ki (t) = di (l) L + Ri (t) + Kw (t) = -Tfriction - Tload (t) Vin (t), dt where vin(t) is the input voltage and Tload(t) is the input load torque. The outputs are the armature current i(t) and the motor speed w(t). When the input voltage and torque are constant, the transient response of this system has the form of the homogeneous solution. What is the time constant of the transient response? Find the characteristic roots of this system first. Keep 3 significant figures, and do not include units. Use scientific notation. The constants are given below: Nominal voltage, Vin(t) = 17 V Moment of inertia of the rotor, J = 0.02 kg-m² Motor viscous friction constant, b = 0.009 N-m-s Friction torque, Tfric = 0.003 N-m Armature inductance, L = 0.1 H Armature resistance, R = 0.35 Back emf constant and motor torque constant, K = 0.21 N-m/A. **Recall that the time constant (or relaxation time) is…
Q1 identify two types of coupling which provide a constant velocity plot. Explain how each coupling type works and their advantages.
The relationship between the force 'F' acting at the end effector and the joint torque '7'is given by O T = (JF)" OT = JFT OT = JF OT = JTF
If the peak power of your electric motor occurs at a torque (Tm) of 0.001 Nm and you have a load (FL) of 1.2 Ibf to pull using a motor, gear box, and winch (rw-0.125 inches). What gear ratio would result in the load moving as fast as possible at equilibrium? Tm Motor Gear Tgb W Воx gb F.
"A 100 kW, 250 V machine-A is in parallel with a 300 kW, 250 V machine-B. The voltage regulation of both machines is 4 percent. Machine-A is carrying 200 Amp and machine- B is carrying 500 Amp. What will be the increment increase in load on machine-A and B respectively (in Amp) if an additional 400 Amp load is connected to the bus?" 100 & 300 300 & 800 400 & 1200 None is correct
HW13/ Home Work: develop a sketch to controlling a servo Motor using a single push bottom as: Assumptions: • Servo Motor connected to PIN 12 • Push bottom connected to PIN 4 • Controlling the angular position of the Servo Motor, each time you press push bottom servo motor moves 45deg from 0-180 deg. v One press moves from 0-45 deg. V Second press moves from 45-90 deg. V Third press moves from 90-135 deg. V Fourth press moves from 135-180 deg. V Fifth press back to 0 deg.
A rotary actuator has the following physical data: Outer radius of rotor = 0.75 in Outer radius of vane = 1.5 in Width of vane = 0.75 in If the torque load is 1000 in lb, what pressure must be developed to overcome the load?
42w6RQJt12D8uMZmCfOin4c7gpb9JWvjWVbvJ89jKd9Tw/formResponse Clear selection A block attached to a spring, oscillates on a frictionless horizontal surface with a period of 0.3 s. The time needed by the block to move (for the first time) from position x = A to x = -A/2 is: O 0.05 sec 0.3 sec O 0.1 sec O 0.15 sec 0.2 sec A simple pendulum consists of a 0.8-kg bob connected to a massless
5. Calculate the brake thermal efficiency of a supercharged 4-cylinder, four stroke cycle Diesel engine with a bore and stroke of 3.94" x 5.91". The compression ratio is 14. Using a brake torque analysis, the dynamometer reads a scale of 143.3 pounds with 13.8 arm at 440 rpm. For a period of 14 minutes of test, 1.433 pounds of fuel with 40,702 KJ/kg heating value are completely burned with air with fuel-air ratio of 0.07 a.) 31.8% b.) 34.1% c.) 32.7% d.) 33.5%