1. A 0.3516 g sample of commercial phosphate detergent was ignited at a heat to destroy the organicmatter. The residue was taken up in hot HCI which converted P to H3PO4. The phosphate was precipitatedas MGNH4PO4.6H2O by addition of Mg+ followed by aqueous NH3. After being filtered and washed, theprecipitate was converted to Mg2P2O7 by ignition at 1000 OC. This residue weighed 0.2161 g. Calculate thepercent P (30.974) in the sample? Ans 17.11%

Answered: Image /qna-images/answer/8e87a923-a9c0-4111-b2bc-a439763501ac.jpg

1. A 0.3516 g sample of commercial phosphate detergent was ignited at a heat to destroy the organic matter. The residue was taken up in hot HCI which converted P to H3PO4. The phosphate was precipitated as MGNH.PO4.6H2O by addition of Mg followed by aqueous NH3. After being filtered and washed, the precipitate was converted to Mg P2O7 by ignition at 1000 OC. This residue weighed 0.2161 g. Calculate the percent P (30.974) in the sample? Ans 17.11%

1. A 0.3516 g sample of commercial phosphate detergent was ignited at a heat to destroy the organic matter. The residue was taken up in hot HCI which converted P to H3PO4. The phosphate was precipitated as MGNH.PO4.6H2O by addition of Mg followed by aqueous NH3. After being filtered and washed, the precipitate was converted to Mg P2O7 by ignition at 1000 OC. This residue weighed 0.2161 g. Calculate the percent P (30.974) in the sample? Ans 17.11%

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

In the laboratory, a student was tasked to prepare a stock solution of HCl for titration. The available analytical grade HCl solution in the stock room was labelled 35% w/v HCl. The student proceeded to prepare the stock solution by mixing 10mL of the HCl solution with 490mL of analytical grade water. Then, the solution was further diluted by adding 5mL, since the total volume of the solution did not reach the 500mL etched mark on the volumetric flask. To prepare the titrant, the student mixed 10mL of the stock solution, then added 40mL of analytical grade water. The titrant was subsequently used to determine the concentration of two titrand. *Use the table as a reference 1. What is the normality of the available HCl reagent in the stock room?* 5.08 N 10.15 N 20.3 N 11.0 N None of the choices 2. What is the normality of the stock solution of HCl?* 0.09N 0.10N 0.11N 0.12N None of the choices 3. What is the normality of the titrant?*…
4. An experiment similar to the one described in this module was performed to determine the solubility and solubility product constant of lead(1l) chloride (gmm = 278.10). The equilibrium involved is PbCl2(s) = Pb2+ (aq) +2 CI¯(aq) The dissolved chloride in the filtered solution was quantitatively precipitated as AgCl by the addition of excess AgNO3 solution. The solid AgCI was filtered from solution, dried, and weighed. The following data were obtained for three samples of the filtered, saturated solution. determination 1 2 temperature of solution, °C volume of PbCl2 solution analyzed, mL mass of dry A£CI, g 20.2 20.4 20.1 25.00 22.00 20.10 0.2543 0.2276 0.2051 Calculate the following: number of moles of: AgCl(s) CI- (aq) Pb2*(aq) [CI"] in PbCl2 solution, M [Pb2+] in PbCl, solution, M Ksp average Ksp solubility of PbCl2, in g per 100 mL chemistry handbook value for solubility at 20°, g per 100 mL
Hh.66.
A 1.250 g sample of bauxite (the primary ore of aluminum) was analyzed for aluminum. The sample was powderized and treated in concentrated nitric acid. The nitric acid was removed and solids were treated in hot water with added nitric acid. Insoluble solids were removed by gravity filtration. The solution was made basic by the slow addition of dilute ammonia forming the gelatinous precipitate (Al(OH), and Al,O,.x H2O). The precipitate was heated to coagulate it then filtered over filter paper. The paper and solids were placed in a porcelain crucible and the paper was ashed while the precipitate was ignited at 600°C to convert the precipitate to pure Al,O,. The mass of Al,O, recovered was 0.2890 g. The average mass of ash after charring 10 sheets of the identical filter paper was 0.0007 g. Calculate the percent aluminum in the bauxite ore sample.
To determine the concentration of glucose in the packaged juice industry, 50 mL of sample is analyzed. Analysis of it (and other reducing sugars) was carried out there using triiodide back titration. An excess volume of 75.00 mL of 0.338 M triiodide standard solution in alkaline medium was added to the glucose solution. The resulting solution was acidified and the excess triiodide was titrated with 18.37 mL of standard 0.526 M thiosulfate solution. Calculate is the concentration in ppm in the sample. In alkaline medium: Glucose (C6H12O6) / Gluconate (C6H11O7-), Triiodide (I3- ) / Iodide (I-) In acid medium: Thiosulfate (S2O32-) / Tetrathionate (S4O62-), Triiodide (I3- ) / Iodide (I-)
Hydroxyapatite, Ca,(PO)(OH)₂, has a solubility constant of K-2.34 x 10-59, and dissociates according to Cao (PO)(OH)₂ (s) = 10 Ca² (aq) + 6PO (aq) + 2OH(aq) Solid hydroxyapatite is dissolved in water to form a saturated solution. What is the concentration of Ca²+ in this solution if JOH is fixed at 8.30 x 10M? |Ca²1 M
A highly acidic (pH< 0.5) industrial wastewater has an initial AlP" concentration of 10 ppm. An engineer decides that strong base should be added to the wastewater in order to raise the pH so that most of the aluminum will precipitate and be removed from solution. The pertinent solubility reaction from Appendix A of our text is: Al(OH)3 (s) → Al* + 30H¯ with pK, = 32.9 a. What is the lowest pH needed to precipitate all but 50 ppb of the aluminum from the wastewater? Assume equilibrium conditions can be achieved. b. Suppose the engineer decides that the pH should be raised to 7. What equilibrium concentration of aluminum would be left in solution? Report your answer in ppb and moles per liter.
A sample containing BaCl, 2H,0, KCI and inert material weighed 0.8417 g. After heating the sample at 160°C for 45 min, it weighed 0.8076 g. The sample was then dissolved in water and treated with a slight excess of AgNo,. The resulting precipitate was collected and found to weigh 0.5847 g. Calculate the % Bacl,-2H,0 and % KCI in the sample. 3.
25 g of the dilute mixture of H2SO4 and HNO3 is completed to 500 mL with water. When BaCl2 is added to 10 mL of this solution, the precipitate obtained is 362 mg. Another 20 mL portion taken from the solution is neutralized with 39.2 mL of 0.2 M NaOH solution in the presence of phenolphthalein. Calculate the percentage of HNO3 in the starting mixture.
In some natural systems the pH must be maintained within very narrow limits. e.g. in human blood the pH must remain close to 7.4 or cell deterioration occurs. Blood contains several weak acid/conjugate base equilibria called buffers, which control the pH.One weak acid present in blood is the dihydrogen phosphate ion, H2PO4-(aq), for which the equilibrium in aqueous solution is H2PO4-(aq) +H2O(l) <--> HPO42-(aq) + H3O+(aq). a) What would be the effect on this equillibrium of adding hydrochloric acid solution?b) Write the expression for the equilibrium constant of this reaction.c) If 0.5 mol H2PO4- and 0.5 mol HPO42- are in equilibrium in 1.0L of aqueous solution, calculate the pH of the solution. (Ka for H2PO4-= 6.4 x 10-8)d) 0.010 mol HCl is now added to the 1.0L of the solution in c). Assuming that all the added H+ ions are used up in the equilibrium shift, calculate the concentrations of H2PO4- and HPO42-. Hence calcuate the pH of this solution.e) 0.010 mol HCl has been added…
A solid sample containing chloride and with a mass equal to 6.000 g was dissolved in water and transferred to a 100.0 ml flask. A 50.0 mL aliquot of this solution was diluted to 250.0 mL. In the titration of 20.0 mL of the diluted solution, 32.0 mL of 0.2000 mol L-1 AgNO3 standard solution were used. Calculate the % of impurities in the analyzed sample. Data: Cl = 35.45
A mixture containing only KCl and NaBr is analyzed by the Mohr method. A 0.2125-g sample is dissolved in 25 mL of water and titrated to the Ag2CrO4 endpoint, requiring 25.63 mL of 0.1110 M AgNO3. A blank titration requires 1.15 mL of titrant to reach the same end point. Report the %w/w KCl and NaBr in the sample. KCl = 74.551 NaBr = 102.89