1) The cylinder consists of spirally wrapped steel plates that are welded at the seams in the orientation shown below is subjected to an internal gage pressure of 400 psi and centric axial loads of P = 15 kips at its rigid end plates. The pressure vessel is fabricated from spirally-welded 0.3-inch thick steel plate. The outside diameter of the pressure vessel is 15 inches. Determine the normal stress perpendicular to the weld, and the shearing stress parallel to the weld.

1) The cylinder consists of spirally wrapped steel plates that are welded at the seams in the orientation shown below is subjected to an internal gage pressure of 400 psi and centric axial loads of P = 15 kips at its rigid end plates. The pressure vessel is fabricated from spirally-welded 0.3-inch thick steel plate. The outside diameter of the pressure vessel is 15 inches. Determine the normal stress perpendicular to the weld, and the shearing stress parallel to the weld.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

Q: Deep sea pipelines are used to transport oil and gas across large distances, at depths greater than…

A: Height of the pipe, h = 2000 mrmin = 400 mDiameter of the pipe, d = 24 inch = 240.0254 = 0.6096 mt=…

Q: A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal…

Q: Consider a rectangular plate shown in Figure 1 and is subjected to a compressive stress of 2.5 MPa…

A: Compressive stress on the x-axis, Tensile stress on the y-axis, The value of the angle,

Q: A typical stainless steel cylindrical vessel is shown. The inside diameter of the tank is 48.0 in.…

Q: The thin-walled pipe has an inner diameter of 2 in. and a thickness of 0.1 in. It is subjected to an…

Q: Fundamental Problem 8.6 Figure 1 200 mm of 1 400 mm -20 mm A Section a-a F₁ F₂ Part A Determine the…

A: Copyfish OCR Result(Auto-Detect)N/ATranslated(English)N/A -->Redo OCR Recapture…

Q: The cylindrical pressure vessel has an inner diameter of 750 mm and a wall thickness of 9 mm. The…

Q: The thin-walled pipe has an inner diameter of 4 in. and a wall thickness of 0.1 in. If it is…

Q: 150 18 F = 25 KN 25 200 25 25 $ -25 100- 25 50 ↑ Calculate the maximum combined stress in the throat…

A: To Find : The maximum combined stress in the throat Given : The load is The free body diagram is,

Q: ximum tensil X1

A: given:length l=400mmthickness b=20mmdepth d=80mm

Q: 8) The pressure tank shown in the next figure is fabricated from spirally wrapped metal plates that…

A: Step 1: Step 2:

Q: Determine the state of stress at point A on the cross section of the pipe at section a - a. Take P=…

A: Data given P = 6.1 kN ro = 50 mm ri = 40 mm

Q: The rectangular bar is connected to the support bracket with a 15-mm-diameter pin. The bar width is…

Q: A compound cylinder is made by shrinking a jacket with an outer diameter of 200 mm on a hollow…

Q: Part A The gas pipe line is supported every 20 ft by concrete piers and also lays on the ground. The…

Question

Q.1) The cylinder consists of spirally wrapped steel plates that are welded at the
seams in the orientation shown below is subjected to an internal gage
pressure of 400 psi and centric axial loads of P = 15 kips at its rigid end
plates. The pressure vessel is fabricated from spirally-welded 0.3-inch thick
steel plate. The outside diameter of the pressure vessel is 15 inches.
Determine the normal stress perpendicular to the weld, and the shearing
stress parallel to the weld.
6 ft.
A
35 deg.
В

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The same circular plate, as in the previous questions, is considered. Assume a plate radius of Ro=490mm and a plate thickness of h=9.64mm, respectively. Also, assume that the plate is subjected to a uniform pressure of P=1,440 KPa, and that the plate is made of a material of Poisson's ratio V=0.34. Find the absolute value of the radial stress at the centre of the plate in KPa. NOTES: type in your answer without considering any negative sign; round-off your answer to 4 decimal places. ↓ r> P Ro VIT
The closed thin-walled tank has an inner radius of r and wall thickness t and contains a gas of pressure of p. The state of stress at point "a" on the surface of the tank is represented by stress components with an unknown stress element rotation angle of 0. Note that, the two normal stress components for x'y' system (note: not xy system!) are known: ox, = 120 MPa and Oy = 180 MPa, but the shear stress component (T,) is unknown. Determine: (1) the principal stresses at point a ; (2) Tx'yı ; (3) rotation angle of 0 . y 180 MPa 120 MPа х 0 = ? a Tyy = ? tank cross section stress state at point a
Solve the problems below: 1. The link acts as part of the elevator control for a small airplane. If the attached aluminum tube has an inner diameter of 25 mm and a wall thickness of 5 mm, determine the maximum shear stress in the tube when the cable force of 600 N is applied to the cables. 600 N 75 mm 5 mm 75 mm -25 mm 600 N
The steel pressure tank shown has a 30-in. inner diameter and a 0.375-in. wall thickness. It is given that the butt-welded seams form an angle β = 50° with the longitudinal axis of the tank and that the gage pressure in the tank is 200 psi. Determine the normal stress perpendicular to the weld. Determine the shearing stress parallel to the weld.
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 500 mm and a wall thickness of 6 mm. Determine the largest allowable gage pressure if the allowable shear stress parallel to the weld is 25 MPa. 50 O 2.63 MPa О 3.13 МРа О 3.36 МРа O 2.88 MPa O 2.44 MPa
strictly don't copy the answer
Two wood members of uniform cross section are joined using a simple glued scarf splice. Determine the normal and shearing stresses in the glued splice. The column is loaded in tension through the centroid with the load indicated. 2.4 kip 6" 60° 2.4 kip
The pressure tank shown is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown where β=55∘β=55∘. The tank has an inside diameter of 26.626.6 in.in. and a wall thickness of 0.3500.350 in.in. Determine the largest gage pressure that can be used inside the tank if the allowable normal stress perpendicular to the weld is 18.518.5 ksiksi and the allowable shear stress parallel to the weld is 8.58.5 ksiksi.
How many 8-mm diameter rivets is needed to fasten member DC to the gusset plate at Cif the member DC has thickness of 8 mm and the working stresses are 15 MPa for shear in the rivets and 20 MPa for bearing due to the rivets. Express your answer to the nearest whole number being the safe value of the rivets to be used. * Sm 40 RN 35 AN
Two solid steel wall supported shafts are connected using the 4 bolt flange. A torque is applied to one side of the bolted connection. Using G = 11.2x10 psi determine the shear stress in the 4" diameter bolts which are on a 2.5" bolt circle diameter. Solve with the applied torque on the left side coupling as shown. Also determine the bolt shear stress if the applied torque was on the other side of the coupling. 1.5 in. 1.25 in. T-350 lb ft 3 ft 2 ft
The pressure tank is fabricated from spirally wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 700 mm and a wall thickness of 8.9 mm. For a gage pressure of 1.27 MPa, determine (a) the normal stress perpendicular to the weld (use positive for tension, negative for compression) and (b) the shear stress (absolute value) parallel to the weld. Assume = 51. s Answers: (a) Normal stress= (b) Shear stress - MPa MPa
The pressure tank shown is fabricated from spirally-wrapped metal plates that are welded at the seams in the orientation shown. The tank has an inside diameter of 48 in. and a wall thickness of 0.375 in. Determine the largest allowable gage pressure if the allowable normal stress perpendicular to the weld is 13 ksi. O 306 psi O 216 psi O 192 psi O 356 psi O 328 psi