The beam below consists of a material with a modulus elasticity of E = 70 GPa and issubjected to a couples of M = 4 kN-m at its end. (a) Calculate the resulting radius of curvature ofthe neutral axis? (b) Calculate the maximum tensile and normal stresses due to bending and statewhere they occur. 1) The beam below consists of a material with a modulus elasticity of E = 70 GPa and issubjected to a couples of M = 4 kN-m at its end. (a) Calculate the resulting radius of curvature ofthe neutral axis? (b) Calculate the maximum tensile and normal stresses due to bending and statewhere they occur.M0.02 m0.03 m 0.02 m0.06 mM0.02 m

Answered: Image /qna-images/answer/b8237349-2e92-4e81-b4c5-94632aec133f.jpg

1) The beam below consists of a material with a modulus elasticity of E = 70 GPa and is subjected to a couples of M = 4 kN-m at its end. (a) Calculate the resulting radius of curvature of the neutral axis? (b) Calculate the maximum tensile and normal stresses due to bending and state where they occur. M 0.02 m 0.03 m 0.02 m 0.06 m M 0.02 m

1) The beam below consists of a material with a modulus elasticity of E = 70 GPa and is subjected to a couples of M = 4 kN-m at its end. (a) Calculate the resulting radius of curvature of the neutral axis? (b) Calculate the maximum tensile and normal stresses due to bending and state where they occur. M 0.02 m 0.03 m 0.02 m 0.06 m M 0.02 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.4.3P: A 4.75-in, outside diameter polyethylene pipe designed to carry chemical waste is placed in a trench...

See similar textbooks

Similar questions

A tie-down on the deck of a sailboat consists of a bent bar boiled at both ends, as shown in the figure. The diameter dBof the bar is 1/4 in., the diameter D Wof the washers is 7/8 in., and the thickness is of the fiberglass deck is 3/8 in. If the allowable shear stress in the fiberglass is 300 psi, and the allowable bearing pressure between the washer and the fiberglass is 550 psi, what is the allowable load P allowon the tie-down?
.4 The stresses on an clement arc known to be sx= 120 MPa, sy= 100 MPa, and txy= 75 MPa. Find the stresses on an inclined section through the element at an angle ? = 45°.
A steel riser pipe hangs from a drill rig located offshore in deep water (see figure). (a) What is the greatest length (meters) it can have without breaking if the pipe is suspended in the air and the ultimate strength (or breaking strength) is 550 MPa? (b) If the same riser pipe hangs from a drill rig at sea, what is the greatest length? (Obtain the weight densities of steel and sea water from Table M, Appendix I. Neglect the effect of buoyant foam casings on the pipe.)
The Z-section of Example D-7 is subjected to M = 5 kN · m, as shown. Determine the orientation of the neutral axis and calculate the maximum tensile stress c1and maximum compressive stress ocin the beam. Use the following numerical data: height; = 200 mm, width ft = 90 mm, constant thickness a = 15 mm, and B = 19.2e. Use = 32.6 × 106 mm4 and I2= 2.4 × 10e mm4 from Example D-7
A circular post, a rectangular post, and a post of cruciform cross section are each compressed by loads that produce a resultant force P acting at the edge of the cross section (see figure). The diameter of the circular post and the depths of the rectangular and cruciform posts are the same. For what width b of the rectangular post will the maximum tensile stresses be the same in the circular and rectangular posts? Repeat part (a) for the post with cruciform cross section. Under the conditions described in parts (a) and (b), which post has the largest compressive stress?
A cantilever beam(Z, = 6 ft) with a rectangular cross section (/> = 3.5 in., h = 12 in.) supports an upward load P = 35 kips at its free end. (a) Find the state of stress ((7T, o^., and r in ksi) on a plane-stress element at L/2 that is i/ = 8 in. up from the bottom of the beam. Find the principal normal stresses and maximum shear stress. Show these stresses on sketches of properly oriented elements. (b) Repeat part (a) if an axial compressive centroidal load N = 40 kips is added at B
Consider the preceding problem if the beam has width h = 15 mm, the aluminum strips have thickness t = 3 mm, the plastic segments have heights d = 40 mm and 3 tf = 120 mm, and the total height of the beam is h = 212 mm. Also, the moduli of elasticity are EA= 75 GPa and Ep=3 GPa, respectively. Determine the maximum stresses o., and o\, in the aluminum and plastic, respectively, due to a bending moment of 1.0 kN - m.
Solve the preceding problem for a box beam with dimensions h = 0.5 m, h = 0.18 m, and t = 22 mm. The yield stress of the steel is 210 MPa.
An aluminum pole for a street light weighs 4600 N and supports an arm that weighs 660 N (see figure). The center of gravity of the arm is 1.2 m from the axis of the pole, A wind force of 300 N also acts in the (y) direction at 9 m above the base. The outside diameter of the pole (at its base) is 225 mm, and its thickness is 18 mm. Determine the maximum tensile and compressive stresses o, and e1., respectively, in the pole (at its base) due to the weights and the wind force.
The cross section of a composite beam made of aluminum and steel is shown in the figure. The moduli of elasticity are TA= 75 GPa and Es= 200 GPa. Under the action of a bending moment that produces a maximum stress of 50 M Pa in the aluminum, what is the maximum stress xs in the steel? If the height of the beam remains at 120 mm and allowable stresses in steel and aluminum are defined as 94 M Pa and 40 M Pa, respectively, what heights h and h. arc required for aluminum and steel, respectively, so that both steel and aluminum reach their allowable stress values under the maximum moment?
For a steel circular cantilever beam, 10mm in diameter, 700mm in length with an applied load of 7.848N in the free end, produce a sketch showing the distribution of stresses across the beam section for an applied moment of M=(3/4My+1/3Mp). Where My=24543.5 N.mm and Mp=41666.66667 N.mm and yeild stregth of material is 250Mpa. Cheers
Is the compressive force (F/A) -180x10^3 since it’s pointing down or is it 180x10^3