1) In the figure shown 3 pipes are in series connection with properties as given asfollows:Pipe NoLength - mDiameter - cmManning'scoefficient1300150.011400200.0113600250.011If the total frictional loss is 5.00 J/N, excluding minor losses, determine the amount ofwater flowing in the pipe system in LPS.32

Answered: Image /qna-images/answer/f3897cb1-d6d4-4631-a17d-e730809efc25.jpg

1) In the figure shown 3 pipes are in series connection with properties as given as follows: Pipe No Length - m Diameter - cm Manning's coefficient 1 300 15 0.011 2 400 20 0.011 3 600 25 0.011 If the total frictional loss is 5.00 J/N, excluding minor losses, determine the amount of water flowing in the pipe system in LPS. 3 2

1) In the figure shown 3 pipes are in series connection with properties as given as follows: Pipe No Length - m Diameter - cm Manning's coefficient 1 300 15 0.011 2 400 20 0.011 3 600 25 0.011 If the total frictional loss is 5.00 J/N, excluding minor losses, determine the amount of water flowing in the pipe system in LPS. 3 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 2: Comparing Three Equations for Head Loss Compare three equations for friction head loss in pipes, assuming constant friction factors. Recall the slope of the energy grade line (EGL) is S = he/L. Part A i. Write the Darcy-Weisbach equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for the friction coefficient, λ? iii. For constant 2, if the discharge is doubled, by what factor does the head loss increase? Part B i. Write the Hazen-Williams equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for the friction coefficient, CHW? iii. For constant Chw, if the discharge is doubled, by what factor does the head loss increase? Part C i. Write the Manning equation for friction head loss, ht=... ii. For iron pipes, what is a typical, midrange value for Manning's n, with units? iii. For constant n, if the discharge is doubled, by what factor does the head loss increase?
A roof tank supplies water as shown in Figure 1. Calculate the minimum height (H) in metre required to maintain a 1.5 m head pressure and 1.0 l/s flow rate at the point of discharge. Given the following data: G.I. pipe diameter d = 25 mm Friction factor f = 0.009 Loss coefficient: ki = 0.2 k2 = 10 Gate Valve Globe Valve Elbow k3 = 2 k4 = 0.5 k5 = 20 Entrance loss at tank Water meter 116 FIGUEE I I un lom'
Use four decimal places in all solution
The diagram below shows a pumping system to pump water to an elevated tank. The next page shows the performance curve of a specific type of centrifugal pump. The loss factors at the inlet and outlet are 0.5 and 1.5 respectively while the loss factor associated with the bend is 1.5. The diameter of the pipe is 0.050 m while the total pipe length is 400 m. In order to simplify the calculation you can assume that the friction factor is f= 0.036. Determine the duty point of this pumping system and thus determine the flow rate of the pump for an impeller diameter of 140 mm? Also determine the shaft power of the pump and give an estimate of the pumps efficiency at the duty point. Given that the pump is located 1.80 m above the water surface (1), and the pipe length from inlet to pump is 6.0 m, determine the NPSHA at the pump and state whether cavitation is likely to occur. Sol: 3.6 m 40 H m 30- P 10 20- K₁ = 0.5 5- kW 2- 1- 13 4 2- NPSH K₁ = 1.5 170 160 150 140. 130_ (1) Q 10 Pump 20 54…
Q4/ Compute the flow rate of water through the 3 pipes connected in series as shown In the Figure below. Let f= 0.016 and neglect minor losses. Pipe No. Diameter of Pipe d (mm) 300 200 250 1 2 3 Water 20 ft Lenth of Pipe L (m) 33 50 40 150 ft. 8-in diameter 120 ft, 10-in diameter 100 ft, 12-in diameter Water Fig. 10-2
A commercial steel pipe—with a diameter, D, of 200 mm and length, L, of 30 m—is used to drain oil (S.G.=0.8)tank. Determine the discharge, in liters per second, when the oil level in the tank is 3 m above the exit of the pipe.Neglect component or minor losses and quantify the friction losses using the Darcy-Weisbach equation shownbelow, use friction factor, f, of 0.12.
I need the answer to the question in fluids
The water surface shown below is 10 m above the datum. The pipe is 425 mm in diameter and the total loss of head between point (1) in the water surface and point (5) in the jet is 3 m. Determine the discharge Q. (m3/s). Round your answers in 3 decimal places.
Q-4 Define coeffecient of velocity, coefficient of discharge, coefficient of contraction. An oil of sp. gr. 0.8 is flowing through a venturimeter having inlet diameter 30 cm and throat diameter 15 cm and the oil- mercury differential manometer shown a reading of 25 cm. Calculate the discharge of oil through the horizontal venturimeter. Take C₁ = 0.98.
1) A manometer is attached to two pipes as shown. If knowing mercury SG is 13.6, sea water SG is 1.035, and fresh water p is 1,000 kg/m³, determine the pressure difference between two pipelines at the centers. Fresh Water h. -60 cm Air hair -70 cm hea <- 40 cm Mercury Sea Water hi -10 cm