1- A rigid bar, pinned at 0, is supported by two identical springs as shown in Fig. Each spring consists of 20 turns of %-in-diameter wire having a mean diameter of 6 in. Determine the maximum load W that may be supported if the shearing stress in the springs is limited to 20 ksi. Answer: W=371.25 lb + 2 ft * 4 ft 3ft

1- A rigid bar, pinned at 0, is supported by two identical springs as shown in Fig. Each spring consists of 20 turns of %-in-diameter wire having a mean diameter of 6 in. Determine the maximum load W that may be supported if the shearing stress in the springs is limited to 20 ksi. Answer: W=371.25 lb + 2 ft * 4 ft 3ft

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Find the magnitude and direction of the resultant force for the system of forces shown in the figure. Where F1 =25 N, F2 =10N, F3 =10 N, F4 =50N, F5 = 10N & F6 =10N. The angles 0, =25°, 03 =25° , 04 = 20°, 06 = 15 ° (Enter only the values in the boxes by referring the units given in bracket) F2 F3 F1 F6 F5 (1) The horizontal component 2H of the given system is (unit is in N) = (2) The vertical component 2 V of the given system is (unit is in N) = (3) The resultant of the given force system is (unit in N) = (4) The direction of Resultant is (in°) =
A person with weight 900 N stands d = 2.00 m away from the wall on a l = 9.00 m beam, as shown in this figure. The weight of the beam is 4,000 N. Define upward as the positive y direction and to the right as the positive x direction. 30° d (a) Find the tension in the wire. (Enter the magnitude only.) N (b) Find the horizontal component of the hinge force. (Indicate the direction with the sign of your answer.) (c) Find the vertical component. (Indicate the direction with the sign of your answer.) N
A standard truck moves across a 25- meter span. The wheel loads are P1=36 kN and P2=142 kN separated by 4.3 m and P3=142 kN at 7.6 m from P2. Calculate the maximum moment. O 156.54 KN.m O204.16 KN.m O 259.7 KN.m O 1409.7 KN.m
Electromagnetism
b Y3 ki F k2 m2 Y1 Figure 1. Consider the mechanical system given in the figure. The system consists of 2 masses, 2 springs and a damper with the given coefficients. The mass of the platform on which the force F is applied is insignificant. The given distances are measured from an equilibrium position. The system acts on a horizontal plane. Hence, gravitational forces are not of any concern. Neglecting rotation and motion in the horizontal direction, the following mathematical relations about the individual components can be written. • Spring 1: F = (y3 – Yı)k1 Spring 2: F, = (y3 – Y2)k2 Damper: Fa = -ý3b
8.Determine the maximum shearing stress in a helical steel spring composed of 20 turns of 20mm diameter wire on a mean radius of 80 mm when the spring is supporting a load of 2 kN.
Determine the smallest force P required to resist the 10.733956 kN force if the static friction coefficient between the rope and the shaft is 0.25
1- The magnetic circuit made of wrought iron is arranged as shown in Fig.1. The central limb has a cross sectional area of 8cm'and each of the side limbs has a cross sectional area of 5cm?. Calculate the ampere turn required to produce a flux of 1mWb in the central limb, neglecting magnetic leakage and fringing. The magnetization of wrought iron is given by: Flux Density (Wb/m²) Field Strength(AT/m) 1 1.25 200 500 1mm 34cm 15cm Fig.1.
QUESTIONS:- 1- Conclusions from experience ? 2-write any five parts of a wind turbine ?
b) The deflecting torque of an instrument directly proportional to the square of the current flowing through it. If a current of 12A produces a deflection of 90°, what deflection would occur for the values of current in the table below when the instrument is (1) Gravity controlled and (2) Spring controlled? State your comments on the results. 1 2 3 4 5 7 8 9 10 0 6 11 12 Current (A) Deflection Angle (0) for Gravity Control Deflection Angle (0) for Spring control
the torque-velocity (T/(w)) relations of the two machines with their shafts clamped together at constant voltage; T1(w)=a1-b1w a1=150Nm b1=1Nm . s/rad T2(w)=a2-b2w a2=270Nm b2=2Nm . s/rad friction will be neglected and there is also no load. In the clamped state, both will try to rotate in the same direction and if voltage is applied in the directions, find the torque, speed and operating mode (motor or generator) of each machine.
(Q.-A): If F2 = 150 lb and e 55°, determine the magnitude and direction measured clockwise from the positive x axis, of the resultant force of the three forces acting on the bracket. Figure (Q,-A)