The magnetic circuit shown in below Fig. 2A is made of a material having relative permeability of 1500. The limb AB is wound with a coil of 800 turns. Find the current through the coil to produce a flux of 4 mWb in the air-gap AE. The length of each air gap is 4mm and the square cross-sectional area of the frame is 4 cm?. C D 30 cm B A G. F 20 cm Fig. 2A.

The magnetic circuit shown in below Fig. 2A is made of a material having relative permeability of 1500. The limb AB is wound with a coil of 800 turns. Find the current through the coil to produce a flux of 4 mWb in the air-gap AE. The length of each air gap is 4mm and the square cross-sectional area of the frame is 4 cm?. C D 30 cm B A G. F 20 cm Fig. 2A.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

13 - Which of the following is true about the magnetic field in the Biot-Savart law?I. is inversely proportional to r.II. It is inversely proportional to r2.III. It is directly proportional to the current. A) Yalnız I B) II ve III C) Yalnız III D) I ve III E) Yalnız II
4. A copper wire has a length of 3500 ft and having an area of 144 cm squared. Find the resistance of the copper conductor at a temperature of 43ºC. 5. The power taken by a resistive coil made of copper wire is 1200W at 120V and 15 °C. Calculate the power consumed by the coil when connected at 250V and 110°C. The temperature coefficient at 27 °C is 0.00393 °C-1.
Two identical coils X and Y of 500 turns each lie in parallel planes such that 80% of flux produced by one coil links with the other. If a current of 5 A flowing in X produces a flux of 10 mWb in it, find the mutual inductance between X and Y
14. A coil with 150 turns is wound over a 200 cm a cylinder iron core whose relative permeability is 250. If a current of 2 A is pass through the coil, determine the flux density in the core. a. 0.04 T b. 0.07 T c. 0.12 T d. 0.10 T
Consider the magnetic circuit given in below figure with parameters: u=153 Ho, d1=9 cm, d236.2 cm, d3=7.9 cm, da=0.3 cm and N=497. Assume that all branches have the same cross-sectional area of 5 cm. Magnetic flux density is 0.1 Wb/m2 in the air gap. Based on the given configuration calculate the current I in [A] in the coil. d2 d3 d, Tolerance + 0.1 relative
b. In the electromechanical system of the figure below, the iron portion has infinite perme ability, and both (b) co-energy W(i, x) pie ces have depth d into the paper. Find: (a) flux linkage at the coil and (c) the for ce acting on the movable piece i(t) W N turns x(t) v(t) N turns
Kindly answer it and show complete solution. Show the given and round off the answer to 2 decimal places
#'s 2-4
Consider the magnetic circuit given in below figure with parameters: u=153 Ho,d1=9 cm, d2=6.2 cm, d3=7.9 cm, d4=0.3 cm and N=497. Assume that all branches have the same cross-sectional area of 5 cm. Magnetic flux density is 0.1 Wb/m2 in the air gap. Based on the given configuration calculate the current I in [A] in the coil. d2 d3 N Tolerance + 0.1 relative
Please compute the torque required for this problem. Thankyou.
Consider the magnetic circuit shown below. The primary coil has N1=400 turns, and the secondary coil has N2=800 turms. The total length of the core (shown in red) is 5 cm. The core has a uniform cross section 2 cm2 , magnetic permeability 900. Calculate the total inductance between terminals a and b, if the coils are connected as shown below. Assume that there is no flux leakage from the core. N1 N2
I need answer within 20 minutes please please with my best wishes