1-75. The hangers support the joist uniformly, so that it is assumed the four nails on each hanger carry an equal portion of the load. If the joist is subjected to the loading shown, determine the average shear stress in each nail of the hanger at ends A and B. Each nail has a diameter of 6 mm. The hangers only support vertical loads. 600 N/m 450 N/m B| 5m

1-75. The hangers support the joist uniformly, so that it is assumed the four nails on each hanger carry an equal portion of the load. If the joist is subjected to the loading shown, determine the average shear stress in each nail of the hanger at ends A and B. Each nail has a diameter of 6 mm. The hangers only support vertical loads. 600 N/m 450 N/m B| 5m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-71. The joint is fastened together using two bolts. Determine the required diameter of the bolts if the failure shear stress for the bolts is Tail 350 MPa. Use a factor of safety for shear of F.S. = 3 40 kN 40 KN 30 mm 80 KN 30 mm
If P=5kN, determine the average shear stress in the pins A, B, and C. All pins are in double shear, and each as a diameter of 18 mm. P 0.5 m B 3P -1.5 m- 2 m 6P -1.5 m- P 0.5 m
A stress element in a rock mass making up a slope experiences a 2D stress as follows: σx = 8 MPa, σy = 4 MPa , tauxy = 3 MPa a. Draw the Mohr circle. On Mohr's circle, mark the location of the x and y planes, mark the angle of rotation θ from the x plane to the σ₁,σ3,and taumax plane. Prove that the angle of rotation of the Mohr circle is 2 times the angle of rotation of the element. b. Write down the coordinates of the center of Mohr's circle and calculate its radius.
Determine the required diameter of the pins at A and B if the allowable shear stress for the material is tallow = 100 MPa. Both pins are subjected to double shear.
The beam is constructed from three boards. Determine the maximum loads P that it can support if the allowable shear stress for the wood is tallow = 400 psi. What is the maximum allowable spacing s of the nails used to holdthe top and bottom flanges to the web if each nail can resist a shear force of 400 lb?
2. The steel pipe has a length of L=24 in. If it is fixed at section C and subjected to the horizontal 200-lb force acting on the handle of the pipe wrench at its end, determine the internal loadings at the section A. 10 in. 14 in 200 lb
Determine the shear stress (in Mpa) in the 22.19-mm-diameter pin at A that support the beam if P = 25.16 kN, a = 2.99 m, and b = 5.03 m. Round off the final answer to three decimal places.
The assembly consists of three disks A, B, and C that are used to support the load of 140 kN. Determine the smallest diameter d₁ of the top disk, and the largest diameter d₂ of the opening, and the largest diameter d3 of the hole in the bottom disk. The allowable bearing stress for the material is (b) allow = 350 MPa and the allowable shear stress is Tallow=125 MPa. C B d₁ -| A 140 kN 20 mm 10 mm d3 d2
Q1/ The prismatic bar has a cross-sectional area A. If it is subjected to a distributed axial loading that increases linearly from w = 0 at x = 0 to w w, at r = a, and then decreases linearly to w 0 at x= 2a, determine the average normal stress in the bar as a function of x for a
Determine the resultant force the bending stress produces on the bottom Flange B (in kip). Express your response using three significant digits. 0.5 in. 3 in. 6 in. M = 10 kip-ft 0.5 in. 0.5 in. 2 in.
The beam has a square cross section and is made of wood having an allowable shear stress of Tallow= 1.4 ksi. If it is subjected to a shear of V= 1.5 kip, determine the smallest dimension a of its sides. Sketch the shear stress distribution acting across the beam's cross section. Hint: Construct the stress distribution in 2D similar to in-class examples, rather than isometrically similar to the textbook examples for clarity. V = 1.5 kip
A lever is attached to a shaft with a square shear key as shown. If the force applied to the lever is P = 395 N, determine the shear force applied to the shear key. 42 mm. ↓ Shear key O 10.90 KN O 18.31 KN O 9.70 KN O 14.25 KN O 13.17 kN 700 mm C Shear key detail