1-35. If the turnbuckle is subjected to an axial force of P = 900 lb, determine the average normal stress developed in section a-a and in each of the bolt shanks at B and C. Each bolt shank has a diameter of 0.5 in. Co -1 in.-

Q: The joint is subjected to a force of P = 2-- lb and F = 150 lb. Determine the state of stress at…

A:

Q: 2-The crimping tool is used to crimp the end of the wire E. If a force of 20 lb is applied to the…

A:

Q: The solid circular rod has a cross-sectional area of 310 mm². It is subjected to a uniform axial…

A:

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A: Given: F1 = 7KN   F2 = 6KN  F3 = 2KN     F4 = 9KN

Q: 1-42. Determine the average shear stress developed in pin A of the truss. A horizontal force of P =…

A: The free body diagram of the truss is as follows:

Q: 2. The bar AC is supported by a pin at A and a cable that runs from B to E around the frictionless…

A: Given data: The allowable stress in the cable is, σa=5.2 ksi. The weight of the cylinder is, w=890…

Q: Use the planar version of Gr¨ubler's formula to determine the number of degrees of freedom of the…

A:

Q: A purse hook is used to hang a handbag from the edge of a table with L = 50 mm. If the cross section…

A: Calculated normal stress at A, B and C and y position where normal stress equals zero

Q: 5-123. The shaft is used to transmit 30 hp while turning at 600 rpm. Determine the maximum shear…

A:

Q: Determine the normal stress in each section of the assembly. The diameter of the solid shaft of each…

A:

Q: how can we determine these values if not given in the problem?

A:

Q: 3-Determine the maximum vertical force P that can be applied to the bell crank so that the average…

A:

Q: The pipe assembly is subjected to the loads shown. Determine the state of stress at point A on…

A: Given data, Let Ax, Ay and Az are the reaction force at A Bx and Bz are the reaction force at B Cz…

Q: Determine the shear stress at point B on the web of the cantilevered strut at section a–a.

A: Given Applied loads 2 kN and 4 kN To find Shear stress at point B

Q: Determine the principal stress and absolute maximum shear stress developed at point B on the cross…

A:

Q: If the allowable tensile stress for wires AB and AC is sallow = 200 MPa, determine the required…

A:

Q: 1-50. The plastic block is subjected to an axial compressive force of 600 N. Assuming that the caps…

A:

Q: Determine the maximum normal stress in the bar. The diameter is 1.5cm. F1 = 7KN   F2 = 6KN   F3 =…

A:

Q: 1-103. The bar is supported by the pin. If the allowable tensile stress for the bar is (o)allow =…

A:

Q: The rib-joint pliers are used to grip the smooth pipe C. If the force of 100 N is applied to the…

A: Given: The magnitude of the force applied on the handles is FH=100 N. The length and breadth of the…

Q: The yoke-and-rod connection is subjected to a 15 tensile force of 5 kN. Determine the average normal…

A:

Q: 5555 40 Ib•ft 20 Ib•ft A B 35 lb-ft 25 lb-ft

A: D =0.75  inR = 0.75/2  in The torque values are shown in the below diagram

Q: The plate has a width of 0.5 m. If the stress distribution at the support varies as shown, determine…

A: Writing equilibrium equations:→∑FY=0 ⇒-P+∫04[(15.x)×(dx×0.5)]=0⇒P=15×23×[x23] 04×0.5⇒P=40 MNNow…

Q: *8-44. Determine the normal stress developed at points A and B. Neglect the weight of the block.

A:

Q: Determine the maximum ram force P that can be applied to the clamp at D if the allowable normal…

A: To find out the centroid…

Machining Processes and Machine Tools

Machining is represented as the process in which an excessive amount of substance is eliminated from the particular element in the form of pieces. In machining, cutting tools such as rotary tools, lathe, drill press, grinder, chop saw, welders, and many more are applied to get the desired shape. As compared to other manufacturing processes, machining is precise and versatile.