03: Assume the diameter of carbon fiber is 7 um and the diameter of glass fiber is 16 µm. Determine the fiber volume fraction in (1) Square array of fiber packing and (2) Triangular array of fiber packing, for fiber spacing-to-fiber diameter ratios (s/d) of 1.0, 1.25, 1.5, 1.75, and 2.0. i. ii. iii. Find the fiber center-to-center spacing for the ratios. Plot the fiber volume fractions and the center-to-center/ diameter Ratios What is the theoretical maximum fiber volume fraction for each of the two composites? Are they dependent on the fiber type or diameter?

03: Assume the diameter of carbon fiber is 7 um and the diameter of glass fiber is 16 µm. Determine the fiber volume fraction in (1) Square array of fiber packing and (2) Triangular array of fiber packing, for fiber spacing-to-fiber diameter ratios (s/d) of 1.0, 1.25, 1.5, 1.75, and 2.0. i. ii. iii. Find the fiber center-to-center spacing for the ratios. Plot the fiber volume fractions and the center-to-center/ diameter Ratios What is the theoretical maximum fiber volume fraction for each of the two composites? Are they dependent on the fiber type or diameter?

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

What is the strength of the ionic interactions between an ion with 1 positive charges and an ion with 1 negative charges, when the distance between them is 24.0 nanometers and the solvent is water, at 25°C with a dielectric constant of 78.57 Calculate answer to 7 decimal places: NB! the comma seperates thousands, the dot is for decimals Do NOT specify units in your answer
3..Suggest how to make syndiotactic/isotactic polystyrene on the one hand and on the other hand how to synthesize atactic polystyrene. Justify your statement.
Calculate and plot the Köhler curves for dry NaCl particles of diameters 40 nm and 100 nm respectively. Calculate the critical supersaturations. Which one will most easily form a cloud droplet? Use surface tension of water, full solubility and u = 2, T = 298K.
How can false low results due to the Hook Effect be accounted for in immunoassay testing?
A thin film of Co was deposited on the end of a long cylinder of Fe3O4. Afterwards, the cylinder was annealed for 20 hours and then the Co concentration was measured. The Co concentration values are given in the table. Calculate the diffusion coefficient of Co in Fe3O4 at the annealing conditions. x (um) C(x,t) (mol/cm³) 7.78x10-4 20 40 7.33x10-4 60 6.64x10-4 80 5.78x10-4
1. calculate the density of water in g/ml. 2. calculate the viscosity of water in cP. *
Short-circuit diffusion means that atomic migration occurs along dislocations, grain boundaries, and external surfaces. dislocations, vacancies, and external surfaces. vacancies, grain boundaries, and external surfaces. dislocations, grain boundaries, and vacancies.
22-30. (a) The mean free path is the average distance a molecule travels before colliding with another molecule. The mean free path, A, is given by A = kT/(V20P), where k is Boltzmann’s constant, T is temperature (K), P is pressure (Pa), and o is the collision cross section. For a molecule with a diameter d, the col- lision cross section is nd. The collision cross section is the area swept out by the molecule within which it will strike any other molecule it encounters. The magnetic sector mass spectrometer is maintained at a pressure of ~103 Pa so that ions do not collide with (and deflect) one another as they travel through the mass analyzer. What is the mean free path of a molecule with a diam- eter of 1 nm at 300 K in the mass analyzer?
Calculate the modulus of elasticity of a metal-matrix composite under isostrain conditions. Assume an aluminum matrix is reinforced by 80 vol % SiC fibers. Express your answer to three significant digits. The modulus of elasticity is Submit Request Answer | ΑΣΦ | | vec ? MPa.
In the solvent hexane, the average end-to-end distance of a 7 kDa molecular weight poly(ethylene glycol) polymer chain is 3.65 nm and the average end-to-end distance of a 56 kDa molecular weight poly(ethylene glycol) polymer chain is 7.30 nm. By calculation, show whether hexane is a good, poor or theta solvent for poly(ethylene (i) glycol).
2. The data below were obtained for a polymerization reaction at 350 K: [M] (kmol / m³) [1] (mol / m³) -d[M]/dt (mol/m³s) 9.04 0.235 0.193 8.63 0.206 0.170 7.19 0.255 0.165 6.13 0.228 0.129 4.96 0.313 0.122 4.75 0.192 0.0937 4.22 0.230 0.0867 Where [M] = monomer concentration and [I] = initiator concentration. Show that the data are consistent with the model for the rate of polymerization by free radical mechanism. Assume that the initiator efficiency is independent of monomer concentration.
Melting Point How will you collect data for this experiment? virtually Melting Point Measurement and Correction Approximate melting point of unknown compound: 85 – 96 °C Select an appropriate melting point standard with a melting point closest to the approximate melting point of your unknown compound. Choose the standard: A. 98 – 100 °C Saved A B. 160 – 162 °C C. 252 - 254 °C Measured absolute melting point of the standard: 96 - 98 °C Measured absolute melting point of the unknown compound: 90 - 94 °C Compare the reported and experimental melting points of the standard to determine if any corrections need be done for your unknown melting point. Correction (°C): 92 - 96 Saved