02): Body A is weight 100 N and ticd to a rigid wall using a steel cable and it is located on body B of weight 00 N which rest on a rough surface (coefficient of fraction is 0.3). If the fraction coefficient between body A nd B is equal to 0.25 and the pulling force P- 600 N, calculate the tension force of the steel cable.

02): Body A is weight 100 N and ticd to a rigid wall using a steel cable and it is located on body B of weight 00 N which rest on a rough surface (coefficient of fraction is 0.3). If the fraction coefficient between body A nd B is equal to 0.25 and the pulling force P- 600 N, calculate the tension force of the steel cable.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.50P: The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the...

See similar textbooks

Similar questions

The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The linkage is made of two homogenous bars of weights shown in the figure. Determine the horizontal force P required to hold the linkage in the position shown.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
With FBD and Solution pls refer to the second picture if the answer is in the choices one of those 4 answers is correct
7. A ladder of length 12 m leaning up against a wall makes a 50 degree angle with the ground. The top of the ladder has sliders so that it can slide up and down the wall. Therefore, consider the top of the ladder to be frictionless. The ladder has a weight of 189 N that acts at its center. Someone weighing Fg = 1000 N is 0.92 m vertically below B, but on the ladder. Another person is on the ground holding the ladder by pushing on it horizontally with a force F. If the coefficient of static friction is 0.32, find the horizontal force F that must be applied at a vertical height of 1.2 m to prevent the ladder from slipping. LL F 1.2 m 12 m 50⁰ Fg B .92 m
Refer to the figure below, what should be the minimum weight of W so that the block of 100ON will not slide down the plane? Assume the pulley to be smooth and u=0.3. 1000N 12
N and Determine the force in cables N necessary to support the 12 kg traffic light shown in figure. (Hint: Please just enter the numerical value without any unit and use three significant digit only. For example if AB= XXX N then enter only XXX.) Answer. = 24 1.63// KSI. 12⁰ B
Can you do it in 15 mints. Thank you
1 help please drw FBD and answer
Required information In the given figure, all pulleys are frictionless. Take the value of P to be 220 lb. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. P 0.5 ft P0.58 --20-20-20- Determine the reactions at point A and the force supported by the cable. (Do not include a minus sign in your response.) The horizontal component of the reaction force at A is lb →. The vertical component of the reaction force at A is The tension in the cable is lb. lb 1.
A uniform horizontal strut weighs 370.0 N. One end of the strut is attached to a hinged support at the wall, and the other end of the strut is attached to a sign that weighs 170.0 N. The strut is also supported by a cable attached between the end of the strut and the wall. Assume that the entire weight of the sign is attached at the very end of the strut. 30° Restaurant Find the tension in the cable (in N). Find the force (in N) at the hinge of the strut. (Give the direction in degrees counterclockwise from the +x-axis. Assume that the +x-axis is to the right.) magnitude direction °counterclockwise from the +x-axis