Activity 1: The boom AB is supported in the position shown by a cable which runs over a small pulley at D. Compute the tension T in the Cable, and the horizontal and vertical components of the reaction at hinge A. Neglect the size of the pulley at D. +300N 1m 500N

Q: Name: Q1/ Give the Name of plans in the Image? The anatomical planes www.free-anatomy-quiz.com Q2/…

A: Plane A -Frontal PlanePlane B -MidSagittal Plane Plane C - Transverse Plane

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: A direction cosine is: O The cosine of the angle between a vector and a particular coordinate axis.…

A:

Q: Q3 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 2:1. 18…

A: Orthographic Projection It is a form of presenting a three-dimensional object into Two dimensional.…

Q: In the figure shown, compute the following : 75 mm 75 mm E 75 mm-

A: Given Shaded area To find Centroid X axis Centroid Y axis

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: 2.34 Determine the resultant of the three forces of Prob. 2.22. Answer

A: Given:The three forces are:F1=800 NF2=408 NF3=424 N

Q: Question 2) Forces of F1 =8 kN in the z direction from the point B in the figure, F 2 =6 kN in the z…

A:

Q: What are 1-, 2-, and 3-point perspectives? Draw cubes of different sizes using 1-, 2-, and 3-point…

A: Approach to solving the question: drawing, constructing of answer Detailed explanation: Examples:Key…

Q: When does the reduction in the dimensions occur?

A: Reducing of dimensions is done in the following conditions. Reducing of dimensions of a workpiece…

Q: Briefly write down the  steps on how to generate (sketch) an involu

A: Involute Profile

Q: Given the isometric drawing of the solid, draw the multiview projection. L HRP FRP L FRP PRP L

A: Given the isometric drawing of the solid, draw the multiview projection.

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: Given the points A( – 5, 6, – 4), B( – 2, — 10, 6), and C(4, 0, 5), find (a) the angle between AB →…

A:

Q: A hammer is balanced at the point "A", close to the metal part. If this hammer is then cut along the…

A: Consider the diagram shown below for the hammer with the center of masses for each side.

Q: In the moment calculation, why did you take away the h* from 8?

A:

Q: z=(x-a} +n(y+b)° 8. Consider the following statements (which statement(s) is/are correct): =2,…

A:

Q: What is the difference between the Ellipse and Polygon drawing methods, while mentioning them in…

A: An ellipse is the set of all points in a plane for which the sum of the distances from the two fixed…

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: To make the circle in an Isometric drawing which geometric option we select from menu bar and why?…

A: 1.To make an isometric drawing of circle we select it from menu bar because we do not have any…

Q: Okay I did everything you did but the only thing I didn't do was take away 10 degrees from my…

A:

Q: An engineer is creating a solid model of a simple gear using SolidWorks. Choose the correct…

A:

Q: An irregular shaped metal sheet is to be constructed with a measurement of 10m x 15m x 20m x 25m. Do…

A:

Q: The positive and negative directions for the X and Y-axes on the mill are determined by the…

A: The mill axis which moves left and right is the x-axis for both vertical and horizontal spindle…

Q: Trace a rough front and top view of a given isometric drawing. Also write the maximum possible steps…

A: The isometric view is given by

Q: Select the correct statement below regarding the two solid model parts shown. (A) (B) It is easiest…

A: In the figure two solid model parts are given. The extrusion is in which the two dimensional shape…

Q: 3- The plane in the space is determined by three points that are not on straightening one O right…

A: Explanation: 3) A plane in space is determined by three points that are not in straight line.  For…

Q: Part A - Construction of Mohr's circle for the state of stress For the element shown, construct…

A: Given Data

Q: Isometric View Top View Front View Right Side Section View

A: Given: Front view is assumed to in the direction shown below,

Q: If the horizontal distance was measured to be 130m and the inclination angle was 25 degrees, what is…

A: Considering a line AB having an inclination angle with horizontal of 25 degrees. The horizontal…

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: The cosine law can be used when two ?angles are already known False

A: To determine whether the given statement is TRUE or FALSE.

Q: How can we find the location of the neutral axis?

A: When a bending moment is applied on a beam, normal stresses are set up in its cross-section due to…

Q: We have a rectangular piece. We wish to manufacture a parallel slot along thepiece in a vertical…

A: Given:To find:What is the number of blades used for the rough cutting steps?What is the number of…

Q: Can you give me an example of laying out compound curves, please include explanation for each…

A:

Q: robotics axis and frames   I am trying to define the axis at each joint, x, y z and whether into…

A: INTRODUCTION : Translations and rotations are based on frames, which are the static coordinate…

Q: Consider for the part in the figure below, a =112, b= 60 and c= 104. 80 Dimensions in mm Analyze the…

A:

Laws of thermodynamics

Thermodynamics is a field of research, which needs the creation of absolute and ideal states and logical and practical examination of the actual conditions. By considering all the laws and theories of thermodynamics, the chemical reactions, the occurrence of processes, and physiological functions can be predicted with this field.