+00000$10ic(a)Fig. 6-11awwBuck-boost Converter6-23. The buck-boost converter of Fig. 6-11 has parameters V = 12 V, D = 0.6, R = 102,L = 10 μH, C = 20 μF, and a switching frequency of 200 kHz. Determine(a) the output voltage, (b) the average, maximum, and minimum inductorcurrents, and (c) the output voltage ripple.

Answered: Image /qna-images/answer/21d2ed9c-279a-43fb-a8b2-289b8623327e.jpg

Answered: +00000 $10 ic (a) Fig. 6-11a ww…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
6:39 Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as silicon and D2 as germanium diodes. Input Vpp=20V, V1=5 V and V2=9 V. www Vin Vout Maximum voltage of output waveform Minimum voltage of output waveform
An inductance coil consumes 500W of power at 10A and 110V and 60HZ. Determine the resistance and the inductance of the coil
1- In a buck DC/DC converter: ton Va = 100 V, R = 80, D ==0.8, f == 20000 Hz, L = 200 μH, Find: a) average voltage and current of the load Vala. b) maximum and minimum current of inductor. c) Voltage ripple of the capacitor. d) the average input current. e) draw the figure of the inductor current. C1 = 40 Micro farad Q Vd - İd K C1 ww + Vo
question in photo please
For full RC charging the constant "n" in the product: "nRC" is "5". Now, which should be the constant "n" in "nRC" such that the voltage in the capacitor is 50% of the supply voltage?
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
Make a clamper circuit using 500 µF capacitor, silicon diode, and a 100 KΩ resistor connected to a 10 Vpeak sine wave. Draw the output waveform and indicate the amplitude and the time values supported by your solutions. Do these for both positive and negative clamper circuit. Show your circuits first before your solutions and waveforms.
i need the answer quickly
The output for the following clamping circuit is shown below assuming ideal diode calculate the avarege value and r.m.s value for the output circuit Vm-10. V-5 (V+ V) V. RL (d) Figure 7-1 simple series clippers (Ideal diodes)
what is the Analysis of AC series Circuits using MATLAB

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS