0.25 m 25 kN B A 0.4 m E 0.2 m In the assembly shown points B and D are connected by double link members BD and points C and E are connected by a single link CE. Each of the three vertical links has an 8x 40-mm uniform rectangular cross section and each of the four pins has a 16-mm diameter. Member ABC has a 12x 50-mm uniform rectangular cross section. For the loading shown, determine 2) The force in link CE (kN) • (Positive if tension and Negative if compression)

0.25 m 25 kN B A 0.4 m E 0.2 m In the assembly shown points B and D are connected by double link members BD and points C and E are connected by a single link CE. Each of the three vertical links has an 8x 40-mm uniform rectangular cross section and each of the four pins has a 16-mm diameter. Member ABC has a 12x 50-mm uniform rectangular cross section. For the loading shown, determine 2) The force in link CE (kN) • (Positive if tension and Negative if compression)

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.63P: The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly...

See similar textbooks

Similar questions

The value of s is equal to 0.8879. answer subparts a, b and c
The uniform rod AB has a weight of 10KN and is supported by a ball-and-socket joint at A and by the cord GC that is attached to the midpoint G of the rod. Knowing that the rod leans against a frictionless vertical wall at B, do the following: a) Label and name all forces that act on the rod. (You may use the given drawing. Assume the weight of the rod acts at G.) (4) 1.5 m 1.5 m b) Determine the tension force in the cable required to hold the rod in equilibrium (21) 4 m G 3m 0.75 75 m- 6 m.
5. Locking Pliers Determine the magnitude of the gripping forces produced when two 50 lb forces are applied as shown. 50 IL 50 lb -0.4 in. 4 in.: 3.2 in. C D 1.2 in. M 1 in. 1.4 in. 1 in. 0.2 in. F = 1.408 kips
The cable of the suspension bridge spans L=140m with a sag H=20m. The cable supports a uniformly distributed load of w0 N/m along the horizontal. If the maximum allowable force in the cable is 4 MN, determine the largest permissible value of w0.
5
A mechanic is reinstalling a newly-sharpened blade on a lawn mower. A wedged-in block of wood at C prevents the blade from rotating as the 29-lb force is applied to the wrench handle. The blade is bolted to a bracket attached to the motor shaft O, which protrudes through the bracket and blade. Determine the normal force at C. State any assumptions. Does it matter whether the bolt at B is installed? 6.5" 2.02.0" 5.9" 29 lb Answer: Nc = i Ib
Pole AB is 12m. long and its weight W = 35kN. It is being lifted using BC and BD. When the pole is tilted at an angle of 60° from the x-axis, the resultant force acts at point A. 'p 2.6 m 3 m 4.5 m 3m 1. Find the tensile force (kN) in cable BC. В. 21.6 A. 22.5 C. 26.1 D. 28.2 2. Find the tensile force (kN) in cable BD. А. 13.1 В. 11.3 С. 14.5 D. 16.1 3. What is the value of the resultant (kN) acting at point A. В. 65.9 А. 69.5 C. 90.6 D. 56.9
Determinethe magnitude (b) of the horizontal component of force at point C if P = 126.6 lb, x= 13.2 in, y = 7 in, and z = 8.6 in Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction : use L if to the left or R if to the right.
DETERMINE ( NEED ONLY HANDWRITTEN SOLUTION PLEASE OTHERWISE DOWNVOTE).
Identify all the 2 force members in the frame shown. A is a built in support and B, C and D are pins. A D 1.5 m 1 m 1 m 2 m В C 3 500 N AB and CD are 2 force members CD is a 2 force member AB, BC and CD are all 2 force members. None of the members are 2 force members. BC and CD are 2 force members. BC is a 2 force member. AB is a 2 force member
Q6: Determine the magnitude of the force supported by the pin at C of the loaded frame.
Determine all forces acting on member ABE of the frame shown in Fig. 150 N 100 mm E 100 mm D B C 100 mm A 200 mm 100 mm