. Water is flowing through a pipe, driven by only gravity (no pumping). a. If water is flowing through a 12-in diameter (completely full), vitrified clay pipe at 3.0 m/s (n = 0.014), what is the slope of the conduit (in m/m)? b. What is the volumetric flow rate through the pipe (in m³/s)? c. If the linear velocity is the same, but the pipe is only 68% full (0.68), what is the volumetric flow rate through the pipe?

. Water is flowing through a pipe, driven by only gravity (no pumping). a. If water is flowing through a 12-in diameter (completely full), vitrified clay pipe at 3.0 m/s (n = 0.014), what is the slope of the conduit (in m/m)? b. What is the volumetric flow rate through the pipe (in m³/s)? c. If the linear velocity is the same, but the pipe is only 68% full (0.68), what is the volumetric flow rate through the pipe?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1.1 Define centrifugal pumps and briefly discuss their operating mechanisms. 1.2 Write the reasons for throttling a pump. What do we do if we do not use throttling? 1.3 Discuss the occurrence of surges in water supply systems and state the potential mitigation mechanisms in big cities. Also explain how pressure surges affects water quality in water supply systems. 1.4 Suppose the selected centrifugal pump for our use is not available in the market. Discuss how you select another pump available in the market and how we can utilize that pump. 1.5 Derive an equation for the available NPSH for a pump is bellow the water in the suction reservoir. Support your derivation by drawing.
26. Inlet and throat diameters of a horizontal venturimeter are 270 mm and 130 mm respectively. The liquid flowing through the venturimeter is water. Pressure intensity at inlet is 19 N/cm2, while pressure at throat is 48 kPa. Find flow rate of water in lit/min, assuming Cd is 0.9 and also draw the neat sketch. i) Actual flow rate =
28. A large tank contains water to a depth of 1.0 m. Water emerges from a small hole in the side of the tank 20 cm below the water level. If the diameter of the hole is 0.50 cm, what is the water flow rate from the hole? (Attach a solution) *
A pipe bends through 900 from its initial direction as shown in fig.13. The pipe reduces in diameter such that the velocity at point (2) is 1.5 times the velocity at point (1). The pipe is 200 mm diameter at point (1) and the static pressure is 100 kPa. The volume flow rate is 0.2 m3/s. Assume there is no friction. Calculate the following. a) The static pressure at (2). b) The velocity at (2). c) The horizontal and vertical forces on the bend FH and Fy. d) The total resultant force on the bend. (1)
5. The below figure shows a pipe with a circular cross section of diameter D= 10 cm. Water enters the left end with a velocity 3 cm/s. The dynamic viscosity of water is 8.90 × 10-4 Pa·s, Find the type of flow. a. No flow b. Laminar flow с. Transitional flow d. Turbulent flow
A Pelton wheel is supplied with 6kg/s of water at 70m/s. The buckets rotate on a mean diameter of 350mm at 1200 rev/min. the deflection angle is 165º and friction negligible. a). Determine the diagram power.(5mks) b). Draw the vector diagram to scale and determine change in water velocity.(5mks)
a) Find the cross-sectional area of the incoming jet (in cm^2) b) Find the horizontal force on the block (in Newtons) (Note: remember to convert the area of the jets from cm^2 to m^2!) c) The vertical force on the block is found to be Fy. What velocity of the incoming jet (i.e. what value of u1) would be needed to generate a force of 4Fy? (Note that you don't need to actually find Fy to solve this question!)
Please give me the solution for the given answer: Ans. 7.88 m/s
5. The flow rate of water through a cast iron pipe is 5000 gallons per minute. The diameter of the pipe is 1 foot, and the coefficient of friction is f = 0.0173. What is the pressure drop over a 100 foot length of pipe?
7) A pump has the following characteristic: Volume flow rate 23 46 69 92 115 (m³/h) Head (m) 17 16 13.5 10.5 6.6 The is used to pump water from a lower tank to a higher tank through a total length of pump 800 m of 150 mm diameter pipe. The difference between the water levels in the two tanks is 8m. Neglecting all losses except friction and assuming that C; = 0.004, find the rate of flow between the two reservoirs. [Ans: = 60m/hr]
Pressure difference required for pipe with elevation change. Water at 68°F is to be pumped through 95 ft of standard 3-in. pipe (internal diameter 3.068 in.) into an overhead reservoir as illustrated in Fig. 6A.2. 30'- Fig. 6A.2 Pipe flow system. 45° elbow 45° elbow Pump 50 45° 15'- (a) What pressure is required at the outlet of the pump to supply water to the overhead reser- voir at a rate of 18 gal/min? At 68°F the viscosity of water is 1.002 cp and the density is 0.9982 g/ml. (b) What percentage of the pressure drop (pump outlet to reservoir) is needed for overcoming the pipe friction? Answer: (a) 15.3 psig
4. Air flows isentropically through the channel To = 300 ° C. both ends have an identical area that is A = 25 cm², pressure p1 = 120 kPa and p2 = 60 kPa. Determine : a). Mass flow rate, b). Throat area C). Ma2